How to remove and install the fan shroud and fan assembly in a Nissan 300ZX?

Disconnect the negative cable at the battery and place the cable out of the way so it cannot accidentally come in contact with the negative terminal of the battery, as this would once again allow power into the electrical system of the vehicle. Remove the radiator shroud retaining bolt securing the shroud to the upper crossmember. From under the vehicle, use a small screwdriver to remove the three retaining clips attaching the shroud to the radiator. Remove the clips by prying up on the retaining clip until the clip can be pried over its plastic retaining tab. At this point the shroud can be lifted out of the engine compartment. Remove the fan and fan coupling from the water pump by removing the four retaining nuts. To separate the fan from the fluid coupling, remove the four retaining bolts. The fan assembly is installed by reversing the above steps. Tighten all fasteners to the proper torque.

Genuine Nissan 300ZX Fan Shroud

Radiator Fan Shroud

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Fan Shrouds found

View related parts
Nissan 300ZX SHROUD-Upper
Part Number: 21476-40P00
$301.34 MSRP: $401.78
You Save: $100.44 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud-Radiator,Upper; Upper Shroud
- Position: Upper
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1990-1996 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VD30DTT, VG30DTT
View related parts
Nissan 300ZX SHROUD-Upper
Part Number: 21476-30P00
$279.95 MSRP: $373.27
You Save: $93.32 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud-Radiator,Upper; Upper Shroud
- Position: Upper
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1990-1996 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VG30D
View related parts
Nissan 300ZX SHROUD-Lower
Part Number: 21477-40P00
$150.91 MSRP: $201.22
You Save: $50.31 (25%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Shroud-Radiator,Lower; Lower Shroud
- Position: Lower
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1990-1996 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VD30DTT, VG30D, VG30DTT
View related parts
Nissan 300ZX Bracket-Motor Fan
Part Number: 21584-51P00
Product Specifications
- Other Name: Shroud
- Manufacturer Note: BRACKET & SHROUD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1994-1996 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VG30D
View related parts
Nissan 300ZX SHROUD-Lower
Part Number: 21476-01P00
Product Specifications
- Other Name: Shroud-Radiator,Lower; Shroud
- Position: Lower
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1984-1989 Nissan 300ZX | GL, GLL, SF, SS | 6 Cyl 3.0L | VG30, VG30T
View related parts
Nissan 300ZX Shroud-Motor Fan
Part Number: 21483-01P00
Product Specifications
- Other Name: Shroud Assy-Radiator
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1984 Nissan 300ZX | GL, GLL, SS | 6 Cyl 3.0L | VG30T
View related parts
Nissan 300ZX Shroud-Motor Fan
Part Number: 21483-01P03
Product Specifications
- Other Name: Shroud Assy-Radiator
- Replaces: 21483-01P13
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1984-1989 Nissan 300ZX | GL, GLL, SS | 6 Cyl 3.0L | VG30T
View related parts
Nissan 300ZX Shroud-Motor Fan
Part Number: 21483-01P13
Product Specifications
- Other Name: Shroud Assy-Radiator
- Replaced by: 21483-01P03
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1987-1989 Nissan 300ZX | GL, GLL, SS | 6 Cyl 3.0L | VG30T
View related parts
Nissan 300ZX Bracket-Motor Fan
Part Number: 21584-30P00
Product Specifications
- Manufacturer Note: BRACKET & SHROUD
- Replaced by: 21584-40P10
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1990 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VG30D
View related parts
Nissan 300ZX Bracket Motor Fan
Part Number: 21584-40P10
Product Specifications
- Other Name: Bracket-Motor Fan; Shroud
- Manufacturer Note: BRACKET & SHROUD
- Replaces: 21584-30P00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1990-1993 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VD30DTT, VG30D, VG30DTT
View related parts
Nissan 300ZX Bracket Motor Fan
Part Number: 21584-40P15
Product Specifications
- Other Name: Bracket-Motor Fan
- Manufacturer Note: BRACKET & SHROUD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1992-1996 Nissan 300ZX | GLL | 6 Cyl 3.0L | VD30DTT, VG30DTT
View related parts
Nissan 300ZX Bracket Motor Fan
Part Number: 21584-30P15
Product Specifications
- Other Name: Bracket-Motor Fan
- Manufacturer Note: BRACKET & SHROUD
- Replaces: 21496-30P15
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1991-1996 Nissan 300ZX | GL, GLL | 6 Cyl 3.0L | VD30DTT, VG30D, VG30DTT
View related parts
Nissan 300ZX Bracket-Motor Fan
Part Number: 21584-53P00
Product Specifications
- Other Name: Shroud
- Manufacturer Note: BRACKET & SHROUD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1995-1996 Nissan 300ZX | GLL | 6 Cyl 3.0L | VD30DTT, VG30DTT
View related parts
Nissan 300ZX SHROUD-Upper
Part Number: 21477-01P00
Product Specifications
- Other Name: Shroud-Radiator,Upper; Shroud
- Position: Rear Upper
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1984-1989 Nissan 300ZX | GL, GLL, SF, SS | 6 Cyl 3.0L | VG30, VG30T

Nissan 300ZX Fan Shroud

The Fan Shroud in Nissan 300ZX vehicles has the main functions of increasing the cooling efficiency of the cooling system. The Fan Shroud encases the cooling fan and enhances on the flow of air hence making the fan to function appropriately in cooling the engine. Second, it is helpful for protecting the fan blades from any possible foreign matters, which is conducive for the prolonging of the cooling system. It is entirely possible that through the years of 300ZX manufacturing there may have been a number of different Fan Shroud designs used, with each being particular to a specific type of engine and/or cooling capacities. The main difference between these types is based in the design and integration into the existing architecture in the vehicle which may impact the over all performance and efficiency of the cooling systems.

If you need any OEM Nissan 300ZX Fan Shroud, feel free to choose them out of our huge selection of genuine Nissan 300ZX Fan Shroud. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan 300ZX Fan Shroud Parts Questions & Experts Answers

SHROUD-Lower
21476-01P00
Q: How to remove and install the fan shroud and fan assembly in a Nissan 300ZX?
A: Disconnect the negative cable at the battery and place the cable out of the way so it cannot accidentally come in contact with the negative terminal of the battery, as this would once again allow power into the electrical system of the vehicle. Remove the Radiator shroud retaining bolt securing the shroud to the upper crossmember. From under the vehicle, use a small screwdriver to remove the three retaining clips attaching the shroud to the radiator. Remove the clips by prying up on the retaining clip until the clip can be pried over its plastic retaining tab. At this point the shroud can be lifted out of the engine compartment. Remove the fan and fan coupling from the Water Pump by removing the four retaining nuts. To separate the fan from the fluid coupling, remove the four retaining bolts. The fan assembly is installed by reversing the above steps. Tighten all fasteners to the proper torque.