How do you remove and install a power steering pump on Nissan Armada?

Remove the power steering pump reservoir by pulling it up off of its bracket. Next, drain the fluid from it and properly dispose of the same and then remove the reservoir bracket by taking out the fasteners. Detach the air intake duct. After this, proceed to remove the drivebelt. Disconnect pressure sensor electrical connector which includes power steering pump electrical connector, pressure line fitting and feed hose clamp. Remove pressure line and feed hose from pump. Discard sealing washers on both sides of the pressure line fitting and cap hoses. Finally, unscrew mounting fasteners and remove pump from vehicle but do not spill fluid on painted surfaces. Use holes in pulley to access power steering pump mounting fastener screws. To install: Position pump onto mounting bracket then install mounting fasteners. Tighten fasteners. Connect pressure line and feed hose to pump. Ensure new sealing washers are used on pressure line fitting and tighten banjo bolt.Install drivebelt.Remaining installation is reversal of removal.Fill recommended fluid into power steering reservoir, then bleed system using method that will be given below.

Genuine Nissan Armada Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Power Steering Pumps found

View related parts
Nissan Armada Pump Assy-Power Steering
Part Number: 49110-7S000
$479.34 MSRP: $732.47
You Save: $253.13 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 49110-ZV00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2010 Nissan Armada | LE, LE/SL, SE, SE/SV | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Armada Pump Power Steering
Part Number: 49110-ZV00A
$479.34 MSRP: $732.47
You Save: $253.13 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Replaces: 49110-7S000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Armada | LE, LE/SL, Platinum, SE, SE/SV | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Armada Pump Power Steering
Part Number: 49110-1LA0B
$644.20 MSRP: $985.22
You Save: $341.02 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Replaces: 49110-5ZA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2023 Nissan Armada | Platinum, Platinum CP, Platinum Reserve | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Armada Pump Power Steering
Part Number: 49110-1LA0A
$511.62 MSRP: $781.97
You Save: $270.35 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Replaces: 49110-5ZA0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2023 Nissan Armada | Midnight Edition, S, SL, SV | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD

Nissan Armada Power Steering Pump

If you need any OEM Nissan Armada Power Steering Pump, feel free to choose them out of our huge selection of genuine Nissan Armada Power Steering Pump. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Armada Power Steering Pump Parts Questions & Experts Answers

Pump Assy-Power Steering
49110-7S000
Q: How do you remove and install a power steering pump on Nissan Armada?
A: Remove the power steering pump reservoir by pulling it up off of its bracket. Next, drain the fluid from it and properly dispose of the same and then remove the reservoir bracket by taking out the fasteners. Detach the air intake duct. After this, proceed to remove the drivebelt. Disconnect pressure sensor electrical connector which includes power steering pump electrical connector, pressure line fitting and feed hose clamp. Remove pressure line and feed hose from pump. Discard sealing washers on both sides of the pressure line fitting and cap hoses. Finally, unscrew mounting fasteners and remove pump from vehicle but do not spill fluid on painted surfaces. Use holes in pulley to access power steering pump mounting fastener screws. To install: Position pump onto mounting bracket then install mounting fasteners. Tighten fasteners. Connect pressure line and feed hose to pump. Ensure new sealing washers are used on pressure line fitting and tighten banjo bolt.Install drivebelt.Remaining installation is reversal of removal.Fill recommended fluid into power steering reservoir, then bleed system using method that will be given below.