How do you properly remove and refit the camshaft position sensor, coolant temperature sensor, crankshaft position sensor, engine control module, fuel injectors, fuel pump, fuel rail, knock sensor, MAP sensor, mass air flow sensor, and spool valve during engine service on Petrol Nissan Juke?

If it is believed that a particular injector is at fault, it may be wise to attempt a proprietary injector-cleaning treatment before coming to a conclusion. undefined 2 litre engines, to replace the Teflon sealing ring at the base of each injector one needs certain Nissan tools and it is wise to consult Nissan or a well done fuel injection expert. After removing the fuel rail and the fuel pipe, they have to be replaced with new ones. Start by turning off the fuel supply system using the primer switch then disconnect the battery negative terminal. Take off the inlet manifold and seal the intake ducts to avoid entry of any material into the cylinder. Remove the high-pressure fuel pipe unions where necessary, clean the union nuts and then, pull out the pipe while sealing the open unions. Remove the wiring connector from fuel pressure sensor and the four fuel injector connectors and then unplug the wiring harness from the fuel rail. Unscrew the retaining bolts and, starting at the inlet port, gently disengage the fuel rail and injectors from cylinder head while shielding the injector pockets against dirt. Remove the retaining clip from each injector and take out the parts then returned the sealing rings, new seals and used components. Refitting involves pulling off the steps mentioned above in reverse and precaution is taken to ensure that new O-rings and Teflon seals are fitted to the engine parts and O-rings coated with engine oil and then fitted back into the engine while checking for fuel leakages when the engine is running. undefined 6 litre engines, the procedure is almost the same but some extra operations involving disconnecting the fuel pipe and wiring harness. Throttle potentiometer, mass airflow sensor, valve timing control solenoids, inlet air temperature sensor, camshaft position sensors, crankshaft position sensor, coolant temperature sensor, knock sensor, air conditioning pressure sensor, manifold pressure sensor and high pressure fuel pump all require particular attention when being removed and refitted which involves disconnecting wires and may also require the removal of bolts and use of new seals during the reassembly.

Genuine Nissan Juke Engine Control Module

Engine Control Computer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Engine Control Modules found

View related parts
Nissan Juke Blank Engine Control Module
Part Number: 23703-BV83A
$923.94 MSRP: $1231.92
You Save: $307.98 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ECM
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC9B
$1045.80 MSRP: $1394.40
You Save: $348.60 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV9A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Blank Engine Control Module
Part Number: 23703-1TV0B
$1302.58 MSRP: $1488.66
You Save: $186.08 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ECM
- Replaces: 23703-1TV0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC7A
$1358.88 MSRP: $1553.00
You Save: $194.12 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV7A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Blank Engine Control Module
Part Number: 23703-BV81A
$1305.09 MSRP: $1491.53
You Save: $186.44 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ECM
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2017 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC6A
$1546.00 MSRP: $1766.86
You Save: $220.86 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV6A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KJ0A
$950.31 MSRP: $1267.08
You Save: $316.77 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZW0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KJ0B
$950.31 MSRP: $1267.08
You Save: $316.77 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZW0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC9A
$1045.80 MSRP: $1394.40
You Save: $348.60 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV9A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module-Blank
Part Number: 23703-1TV0A
$1302.58 MSRP: $1488.66
You Save: $186.08 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23703-1TV0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC7C
$1358.88 MSRP: $1553.00
You Save: $194.12 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV7A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC6B
$1546.00 MSRP: $1766.86
You Save: $220.86 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV6A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC6C
$1546.00 MSRP: $1766.86
You Save: $220.86 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV6A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC8A
$1585.56 MSRP: $1812.07
You Save: $226.51 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV8A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module Assembly
Part Number: 23710-1KC8B
$1585.56 MSRP: $1812.07
You Save: $226.51 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assy Engine Control
- Replaced by: 23710-1ZV8A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC8C
$1585.56 MSRP: $1812.07
You Save: $226.51 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23710-1ZV8A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC9C
$1045.80 MSRP: $1394.40
You Save: $348.60 (25%)
ADD TO CART
Product Specifications
- Other Name: ECM
- Replaced by: 23710-1ZV9A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KJ0C
$950.31 MSRP: $1267.08
You Save: $316.77 (25%)
Product Specifications
- Replaced by: 23710-1ZW0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Luxury, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Control Module
Part Number: 23710-1KC7B
Product Specifications
- Replaced by: 23710-1ZV7A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, S | 4 Cyl 1.6L | MR16DDT

Nissan Juke Engine Control Module

If you need any OEM Nissan Juke Engine Control Module, feel free to choose them out of our huge selection of genuine Nissan Juke Engine Control Module. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Juke Engine Control Module Parts Questions & Experts Answers

Engine Control Module
23710-1KC7A
Q: How do you properly remove and refit the camshaft position sensor, coolant temperature sensor, crankshaft position sensor, engine control module, fuel injectors, fuel pump, fuel rail, knock sensor, MAP sensor, mass air flow sensor, and spool valve during engine service on Petrol Nissan Juke?
A: If it is believed that a particular injector is at fault, it may be wise to attempt a proprietary injector-cleaning treatment before coming to a conclusion. undefined 2 litre engines, to replace the Teflon sealing ring at the base of each injector one needs certain Nissan tools and it is wise to consult Nissan or a well done fuel injection expert. After removing the fuel rail and the fuel pipe, they have to be replaced with new ones. Start by turning off the fuel supply system using the primer switch then disconnect the battery negative terminal. Take off the inlet manifold and seal the intake ducts to avoid entry of any material into the cylinder. Remove the high-pressure fuel pipe unions where necessary, clean the union nuts and then, pull out the pipe while sealing the open unions. Remove the wiring connector from fuel pressure sensor and the four fuel injector connectors and then unplug the wiring harness from the fuel rail. Unscrew the retaining bolts and, starting at the inlet port, gently disengage the fuel rail and injectors from cylinder head while shielding the injector pockets against dirt. Remove the retaining clip from each injector and take out the parts then returned the sealing rings, new seals and used components. Refitting involves pulling off the steps mentioned above in reverse and precaution is taken to ensure that new O-rings and Teflon seals are fitted to the engine parts and O-rings coated with engine oil and then fitted back into the engine while checking for fuel leakages when the engine is running. undefined 6 litre engines, the procedure is almost the same but some extra operations involving disconnecting the fuel pipe and wiring harness. Throttle potentiometer, mass airflow sensor, valve timing control solenoids, inlet air temperature sensor, camshaft position sensors, crankshaft position sensor, coolant temperature sensor, knock sensor, air conditioning pressure sensor, manifold pressure sensor and high pressure fuel pump all require particular attention when being removed and refitted which involves disconnecting wires and may also require the removal of bolts and use of new seals during the reassembly.

Related Nissan Juke Parts

Browse by Year

2017 Engine Control Module 2016 Engine Control Module 2015 Engine Control Module 2014 Engine Control Module 2013 Engine Control Module 2012 Engine Control Module 2011 Engine Control Module