Contact Us: Live Chat or 1-888-726-6993
My Garage
My Account
My Cart

Genuine Nissan Quest Distributor Rotor

Ignition Distributor Rotor

Enter your vehicle info to find more parts and verify fitment

  • Select Vehicle by VIN
  • Select Vehicle by Model
Select by VIN
Enter your VIN for the most accurate results.
Enter your VIN for the most accurate results.
or
Select by Model
-- Select Model --
-- Select Year --

2 Distributor Rotors found

  • Nissan Quest Distributor Rotor - 22157-85E01
    Diagram for Nissan Quest Distributor Rotor - 22157-85E01
    View related parts

    Nissan Quest Rotor-Head

    Part Number: 22157-85E01
    $10.86 MSRP: $14.48
    You Save: $3.62 (25%)
    Add to Cart
    Product Specifications
    • Other Name: Rotor
    • Replaces: 22157-85E00
    • Warranty: This genuine part is guaranteed by Nissan's factory warranty.
    View More
    Fits the following Vehicles:
    • 1993-1998 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
  • Nissan Quest Distributor Rotor - 22157-1W600
    Diagram for Nissan Quest Distributor Rotor - 22157-1W600
    View related parts

    Nissan Quest Rotor Head

    Part Number: 22157-1W600
    $13.29 MSRP: $17.72
    You Save: $4.43 (25%)
    Add to Cart
    Product Specifications
    • Other Name: Rotor-Head; Rotor
    • Manufacturer Note: HITACHI
    • Replaces: 22157-1W601
    • Warranty: This genuine part is guaranteed by Nissan's factory warranty.
    View More
    Fits the following Vehicles:
    • 1999-2003 Nissan Quest | GXE, SE | 6 Cyl 3.3L | VG33E

Nissan Quest Distributor Rotor Parts Questions & Answers

  • Q: How to check and install spark plug wires,Distributor Cap and Distributor Rotor on Nissan Quest?
    A: check the wires of the Spark Plug for any problems that need attention. Inspect visually the wires as the engine runs in an area with enough ventilation. In case there are damaged areas, check for signs of sparking or arcing. If arcing is seen, it should be noted that the distributor cap and rotor should only be checked after replacing them. To ascertain the right order of wires, inspect them individually and write down their numbers or use marked tape if they cannot be visible. While removing a wire from a spark plug, just employ a puller or twist out with soft boots avoiding any tension on themselves. After attaching the boots back onto its respective plug, ensure that it fits well without having any defects or poor contact. Clean it using a piece of cloth rag, look at it keenly for burns and avoid forming sharp bends on it. Pull off the distributor cap by pulling up on its boot; after that, test for tightness as well as corrosion. Closely look at both wires going from your distributor to each spark plug to verify they are all connected properly. If you need new spark plug wires, buy an entire set specifically made for your type of engine so you can change them one by one while keeping the firing order intact. The distributor cap should also be examined for cracks, carbon tracks and worn out/burned contacts which have occurred over time and thus are no longer functional while the rotor needs to be gone through for cracks and carbon tracks. Replace the cap and rotor as needed when installing new spark plug wires. If you are reusing your old cap then measure resistance between spark plug wires and cap; replace any whose resistance exceeds maximum value. Whenever you are putting in brand-new caps do it sequentially so that you don't break this order otherwise refer to firing order diagrams in case of confusion.

Related Nissan Quest Parts