How do you properly remove and install a steering gear assembly on Nissan Quest?

Loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands. Apply the parking brake and remove the front wheels along with the engine splash shields. Place a drain pan under the Rack And Pinion, detach the power steering pressure and return lines, and cap the ends to prevent excessive fluid loss and contamination. Remove the master cylinder reservoir mounting screws and position the reservoir off to the side without disconnecting the brake hoses, using wire to support it. Remove the front stabilizer bar and separate the tie-rod ends from the steering knuckle arms. From inside the vehicle, remove the universal joint cover by taking out the U-joint cover nuts, slide the boot up for clearance, and remove the pinch bolt from the upper section of the steering shaft. Support the Rack And Pinion and remove the Rack And Pinion mounting bolts, lower the Rack And Pinion slightly, and remove the intermediate shaft-to-Rack And Pinion pinch bolt, separating the intermediate shaft from the Rack And Pinion input shaft to pull the Rack And Pinion assembly out towards the driver's side. Check the Rack And Pinion rubber mounts for excessive wear or deterioration, replacing them if necessary. Before installing, ensure the Rack And Pinion is centered from side-to-side, then slide it into position from the driver's side, connect the intermediate shaft to the Rack And Pinion, and install and tighten the pinch bolt. Raise the Rack And Pinion into position and connect the upper section of the intermediate shaft onto the steering column. Install the mounting brackets and bolts, ensuring the UP mark on the brackets is correctly positioned, then tighten all bolts snugly at first before following the recommended tightening sequence to achieve the proper torque. Connect the tie-rod ends to the steering knuckle arms, install the intermediate shaft-to-steering column pinch bolt, and tighten it to the torque. Connect the power steering pressure and return hoses to the Rack And Pinion, filling the power steering pump reservoir with the recommended fluid. Finally, install the wheels and lug nuts, lower the vehicle, tighten the lug nuts to the torque, and bleed the steering system.

Genuine Nissan Quest Rack And Pinion

Steering Rack And Pinion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Rack And Pinions found

View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA2A
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering; Gear Assembly
- Replaces: 49001-1JA0B, 49001-1JA0D, 49001-1JA0A, 49001-1JA1E, 49001-1JA0E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-ZM71B
$1367.81 MSRP: $1558.41
You Save: $190.60 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering; Gear Assembly, Steering Gear
- Replaces: 49001-ZM70A, 49001-CK000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2010 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rack Assy-Power Steering
Part Number: 49271-1JB0A
$279.64 MSRP: $388.49
You Save: $108.85 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2014 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rack Assy-Power Steering
Part Number: 49271-1JA0A
$503.63 MSRP: $671.50
You Save: $167.87 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA0A
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-1JA2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA0B
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-1JA2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2013 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA0D
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-1JA2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2013 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA0E
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-1JA2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2015 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage
Part Number: 49001-1JA1E
$1304.70 MSRP: $1711.04
You Save: $406.34 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-1JA2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2015 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear Assy-Power Steering
Part Number: 49200-1JA0D
$2788.38 MSRP: $3375.76
You Save: $587.38 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear, Steering Gear
- Replaces: 49200-1JA1E, 49200-1JA0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage-Power Steering
Part Number: 49001-CK000
$1367.81 MSRP: $1558.41
You Save: $190.60 (13%)
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-ZM71B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2007 Nissan Quest | S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear & Linkage-Power Steering
Part Number: 49001-ZM70A
$1367.81 MSRP: $1558.41
You Save: $190.60 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-ZM71B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2007 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear Assembly - Power Steering
Part Number: 49200-1JA0B
$2953.79 MSRP: $3375.76
You Save: $421.97 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear Assy-Power Steering
- Replaced by: 49200-1JA0D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2013 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear Assy-Power Steering
Part Number: 49200-1JA1E
$2953.79 MSRP: $3375.76
You Save: $421.97 (13%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 49200-1JA0D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Gear Assy-Power Steering
Part Number: 49200-0B000
Product Specifications
- Other Name: Housing Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1998 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest Gear & Linkage - Power Steering
Part Number: 49001-0B001
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1996-1998 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest Gear & Linkage-Power Steering
Part Number: 49001-0B000
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering
- Replaced by: 49001-7B000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1997 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest Gear & Linkage-Power Steering
Part Number: 49001-7B000
Product Specifications
- Other Name: Gear & Linkage Assy-Power Steering; Gear Assembly, Steering Gear
- Replaces: 49001-0B000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2003 Nissan Quest | GXE, SE | 6 Cyl 3.3L | VG33E
- 1993-1997 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest Gear Assy-Power Steering
Part Number: 49200-1JA0A
Product Specifications
- Other Name: Gear, Steering Gear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE

Nissan Quest Rack And Pinion

If you need any OEM Nissan Quest Rack And Pinion, feel free to choose them out of our huge selection of genuine Nissan Quest Rack And Pinion. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Quest Rack And Pinion Parts Questions & Experts Answers

Gear Assy-Power Steering
49200-0B000
Q: How do you properly remove and install a steering gear assembly on Nissan Quest?
A: Loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands. Apply the parking brake and remove the front wheels along with the engine splash shields. Place a drain pan under the Rack And Pinion, detach the power steering pressure and return lines, and cap the ends to prevent excessive fluid loss and contamination. Remove the master cylinder reservoir mounting screws and position the reservoir off to the side without disconnecting the brake hoses, using wire to support it. Remove the front stabilizer bar and separate the tie-rod ends from the steering knuckle arms. From inside the vehicle, remove the universal joint cover by taking out the U-joint cover nuts, slide the boot up for clearance, and remove the pinch bolt from the upper section of the steering shaft. Support the Rack And Pinion and remove the Rack And Pinion mounting bolts, lower the Rack And Pinion slightly, and remove the intermediate shaft-to-Rack And Pinion pinch bolt, separating the intermediate shaft from the Rack And Pinion input shaft to pull the Rack And Pinion assembly out towards the driver's side. Check the Rack And Pinion rubber mounts for excessive wear or deterioration, replacing them if necessary. Before installing, ensure the Rack And Pinion is centered from side-to-side, then slide it into position from the driver's side, connect the intermediate shaft to the Rack And Pinion, and install and tighten the pinch bolt. Raise the Rack And Pinion into position and connect the upper section of the intermediate shaft onto the Steering Column. Install the mounting brackets and bolts, ensuring the UP mark on the brackets is correctly positioned, then tighten all bolts snugly at first before following the recommended tightening sequence to achieve the proper torque. Connect the tie-rod ends to the steering knuckle arms, install the intermediate shaft-to-steering column pinch bolt, and tighten it to the torque. Connect the power steering pressure and return hoses to the Rack And Pinion, filling the power steering pump reservoir with the recommended fluid. Finally, install the wheels and lug nuts, lower the vehicle, tighten the lug nuts to the torque, and bleed the steering system.