What are the steps recommended by the manufacturer for adjusting valve clearance on Nissan Sentra?

The manufacturer recommends adjusting the valve clearance at the specified interval only if the valve train is making excessive noise. Begin by disconnecting the cable from the negative terminal of the battery. Next, remove the intake manifold on 2.0L models and the valve cover on all models. For manual transaxle vehicles, set the parking brake and place the transaxle in Neutral. Remove the spark plugs and position the number 1 piston at TDC on the compression stroke, aligning the timing marks. Measure the clearance of the indicated valves with a feeler gauge, noting that you will feel drag if the adjustment is correct. Record each measurement and compare them with the desired valve clearance specifications, noting any that are out of specification for later reference. Turn the crankshaft one complete revolution, realign the timing marks, and measure and record the clearances of the valves again. These engines do not use valve adjusting shims; if a clearance is out of specification, the lifter must be replaced with a new lifter of a different thickness to correct the clearance. Remove the camshafts to access the lifters, mark those to be replaced, and record which valve they came from. Measure the thickness of the center of the lifter with a micrometer. To calculate the correct thickness of a replacement lifter that will place the valve clearance within the specified value, use the formula N=T+A-V, where N is the thickness of the new lifter, T is the thickness of the old lifter, A is the valve clearance measured, and V is the desired valve clearance. Select a lifter with a thickness as close as possible to the calculated valve clearance, as lifters are marked on the underside for size. Mark the new lifters for their destination, lubricate them with engine assembly lube, and install them. After replacing the lifters, install the camshaft(s). The remainder of the installation is the reverse of removal, followed by reconnecting the battery and performing the necessary re-learn procedures.

Genuine Nissan Sentra Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Intake Valves found

View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-3RC0A
$10.31 MSRP: $13.75
You Save: $3.44 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Manufacturer Note: INT
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2019 Nissan Sentra | FE, S, SL, SR, SV | 4 Cyl 1.8L | MRA8DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-0M200
$12.89 MSRP: $17.18
You Save: $4.29 (25%)
ADD TO CART
Product Specifications
- Replaced by: 13201-4M700
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1995-2006 Nissan Sentra | 1.8, 1.8S, Base, GLE, GXE, S, SE, XE | 4 Cyl 1.6L, 4 Cyl 1.8L | GA16DE, QG18DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-BV81A
$19.95 MSRP: $26.60
You Save: $6.65 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13201-BV81B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Sentra | Nismo, SR | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-3Z000
$7.29 MSRP: $9.72
You Save: $2.43 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13201-3Z00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2001-2005 Nissan Sentra | 2.5S, LE, SE-R, SE-R Spec V | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-EN20A
$13.36 MSRP: $17.82
You Save: $4.46 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13201-EN20E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Sentra | 20 | 4 Cyl 2.0L | MR20DE
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-4M700
$12.89 MSRP: $17.18
You Save: $4.29 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve-Intake; Intake Valve
- Replaces: 13201-57Y00, 13201-70N00, 13201-0M200
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1991-2006 Nissan Sentra | 1.8, 1.8S, Base, CA, GLE, GXE, S, SE, STD, XE | 4 Cyl 1.6L, 4 Cyl 1.8L | GA16DE, J/GA16DE, QG18DE, U/GA16DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-57Y00
$12.89 MSRP: $17.18
You Save: $4.29 (25%)
ADD TO CART
Product Specifications
- Replaced by: 13201-4M700
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1991-1993 Nissan Sentra | GXE, STD, XE | 4 Cyl 1.6L | J/GA16DE, U/GA16DE
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-3Z00A
$7.29 MSRP: $9.72
You Save: $2.43 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve-Intake; Intake Valve
- Replaces: 13201-3Z000, 13201-3Z001
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2001-2006 Nissan Sentra | 2.5S, LE, SE-R, SE-R Spec V | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-3Z001
$7.29 MSRP: $9.72
You Save: $2.43 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve-Intake
- Replaced by: 13201-3Z00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2006 Nissan Sentra | 2.5S, LE, SE-R, SE-R Spec V | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-01M00
$7.41 MSRP: $9.88
You Save: $2.47 (25%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Valve-Intake
- Replaced by: 13201-05M00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1982-1984 Nissan Sentra | DX, STD, XE | 4 Cyl 1.5L, 4 Cyl 1.6L | E15, E16
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-53J00
$28.51 MSRP: $38.02
You Save: $9.51 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1991-1994 Nissan Sentra | SE, SR | 4 Cyl 2.0L | J/SR20DE, U/SR20DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-BV81B
$19.95 MSRP: $26.60
You Save: $6.65 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Replaces: 13201-BV81A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Sentra | Nismo, SR | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-70N00
$12.89 MSRP: $17.18
You Save: $4.29 (25%)
ADD TO CART
Product Specifications
- Replaced by: 13201-4M700
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1991-1994 Nissan Sentra | GXE, SE, STD, XE | 4 Cyl 1.6L | J/GA16DE, U/GA16DE
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-6LB0A
$14.24 MSRP: $18.98
You Save: $4.74 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2023 Nissan Sentra | S, SR, SV | 4 Cyl 2.0 L GAS
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-JA00A
$5.44 MSRP: $7.25
You Save: $1.81 (25%)
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Sentra | SE-R, Spec V | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-84A00
Product Specifications
- Other Name: Valve-Intake; Intake Valve
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1988-1990 Nissan Sentra | Base, GXE, SE, STD, XE | 4 Cyl 1.6L | GA16I
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-31M00
Product Specifications
- Other Name: Valve-Intake
- Replaced by: 13201-69A00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1982-1988 Nissan Sentra | Base, DX, GXE, SE, STD, XE | 4 Cyl 1.6L | E16, E16I, E16S
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-69A00
Product Specifications
- Other Name: Intake Valve
- Replaces: 13201-31M00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1982-1989 Nissan Sentra | Base, DX, GXE, SE, STD, XE | 4 Cyl 1.6L | E16, E16I, E16S
View related parts
Nissan Sentra Valve Intake
Part Number: 13201-16A00
Product Specifications
- Other Name: Valve-Intake
- Replaced by: 13201-87R00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1982-1986 Nissan Sentra | DX | 4 Cyl 1.7L | CD17
View related parts
Nissan Sentra Valve-Intake
Part Number: 13201-1E700
Product Specifications
- Replaced by: 13201-1E711
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1995-1996 Nissan Sentra | SE-R | 4 Cyl 2.0L | SR20DE

| Page 1 of 2 |Next >

1-20 of 22 Results

Nissan Sentra Intake Valve

If you need any OEM Nissan Sentra Intake Valve, feel free to choose them out of our huge selection of genuine Nissan Sentra Intake Valve. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Sentra Intake Valve Parts Questions & Experts Answers

Valve-Intake
13201-EN20A
Q: What are the steps recommended by the manufacturer for adjusting valve clearance on Nissan Sentra?
A: The manufacturer recommends adjusting the valve clearance at the specified interval only if the valve train is making excessive noise. Begin by disconnecting the cable from the negative terminal of the battery. Next, remove the intake manifold on 2.0L models and the valve cover on all models. For manual transaxle vehicles, set the parking brake and place the transaxle in Neutral. Remove the Spark Plugs and position the number 1 piston at TDC on the compression stroke, aligning the timing marks. Measure the clearance of the indicated valves with a feeler gauge, noting that you will feel drag if the adjustment is correct. Record each measurement and compare them with the desired valve clearance specifications, noting any that are out of specification for later reference. Turn the crankshaft one complete revolution, realign the timing marks, and measure and record the clearances of the valves again. These engines do not use valve adjusting shims; if a clearance is out of specification, the lifter must be replaced with a new lifter of a different thickness to correct the clearance. Remove the camshafts to access the lifters, mark those to be replaced, and record which valve they came from. Measure the thickness of the center of the lifter with a micrometer. To calculate the correct thickness of a replacement lifter that will place the valve clearance within the specified value, use the formula N=T+A-V, where N is the thickness of the new lifter, T is the thickness of the old lifter, A is the valve clearance measured, and V is the desired valve clearance. Select a lifter with a thickness as close as possible to the calculated valve clearance, as lifters are marked on the underside for size. Mark the new lifters for their destination, lubricate them with engine assembly lube, and install them. After replacing the lifters, install the camshaft(s). The remainder of the installation is the reverse of removal, followed by reconnecting the battery and performing the necessary re-learn procedures.