How to remove and install the caliper on Nissan Titan?

On Armada models equipped with a rear auto-leveling suspension, turn the ignition key to the OFF position before raising the vehicle. This procedure applies to the front and rear disc brake calipers. To remove, loosen the wheel lug nuts, raise the vehicle and place it securely on jackstands. Block the wheels at the opposite end. Remove the wheel. For front caliper (all models) and rear caliper (Armada models), disconnect the brake hose from the caliper. Discard the old sealing washers. Plug the brake hose immediately to keep contaminants and air out of the brake system and to prevent losing any more brake fluid than is necessary. If you are simply removing the caliper for access to other components, leave the brake hose connected. Remove the caliper mounting bolts and detach the caliper. If the hose is still connected, secure the caliper with wire and don't let it hang by the hose. For rear caliper (Titan models), break loose the brake hose fitting, but don't unscrew it yet. If you're just removing the caliper for access to other components, don't loosen the hose. Remove the caliper mounting bolts, detach the caliper, then unscrew the caliper from the brake hose. If you intend to leave the hose connected, secure the caliper with wire and don't let it hang by the brake hose. For installation, the process is the reverse of removal. Don't forget to use new sealing washers on each side of the brake hose inlet fitting and be sure to tighten the fitting bolt and the caliper mounting bolts to the torque values. For rear caliper (Titan models), install a new sealing washer on the brake hose. Thread the caliper onto the brake hose as far as possible, but don't tighten the hose with a wrench yet. Install the caliper and mounting bolts, tightening the bolts to the torque. Tighten the brake hose securely. Make sure the hose isn't twisted. Finally, bleed the brake system. If the brake hose was not disconnected, bleeding won't be required. Make sure there are no leaks from the hose connections. Test the brakes carefully before returning the vehicle to normal service.

Genuine Nissan Titan Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Brake Calipers found

View related parts
Nissan Titan CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-7S010
$345.87 MSRP: $458.38
You Save: $112.51 (25%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim; Caliper
- Position: Driver side
- Replaced by: 41011-7S010RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan CALIPER Assembly-Front RH, W/O Pads Or SHIMS
Part Number: 41001-ZC60A
$282.41 MSRP: $470.20
You Save: $187.79 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-ZC60B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2019 Nissan Titan | LE, Off-Road, Platinum, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Rear LH,W/O Pads Or SHIMS
Part Number: 44011-7S000
$247.18 MSRP: $354.62
You Save: $107.44 (31%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 44011-7S000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan CALIPER Assembly-Front RH, W/O Pads Or SHIMS
Part Number: 41001-7S010
$345.87
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM; Caliper
- Position: Passenger Side
- Replaced by: 41001-7S010RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-ZC60B
$308.34 MSRP: $470.20
You Save: $161.86 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER
- Position: Front Passenger Side
- Replaces: 41001-ZC60A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Titan | Platinum Reserve, PRO-4X, S, SL, SV | 8 Cyl 5.6 L GAS
View related parts
Nissan Titan CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-ZC60B
$308.34 MSRP: $470.20
You Save: $161.86 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim; Caliper
- Position: Driver side
- Replaces: 41011-ZC60A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2024 Nissan Titan | LE, Off-Road, PRO-4X, Platinum, Platinum Reserve, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan Caliper Assy-Rear LH,W/O Pad & Shim
Part Number: 44011-1PA1C
$138.43 MSRP: $256.71
You Save: $118.28 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Driver side
- Replaces: 44011-1PA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-ZC60A
$282.41 MSRP: $470.20
You Save: $187.79 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-ZC60B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2019 Nissan Titan | LE, Off-Road, Platinum, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan Caliper Assy-Rear RH,W/O Pad & Shim
Part Number: 44001-1PA1C
$138.43 MSRP: $255.00
You Save: $116.57 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Passenger Side
- Replaces: 44001-1PA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan Caliper Assy-Front LH,W/O Pad & Shim
Part Number: 41011-1PA1B
$301.13 MSRP: $459.14
You Save: $158.01 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Driver side
- Replaces: 41011-1PA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front RH,W/O Pad & SHIM
Part Number: 41001-1PA1B
$301.13 MSRP: $459.14
You Save: $158.01 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Passenger Side
- Replaces: 41001-1PA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Rear RH,W/O Pads Or SHIMS
Part Number: 44001-1PA1A
$119.02 MSRP: $255.00
You Save: $135.98 (54%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim
- Position: Passenger Side
- Replaced by: 44001-1PA1C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front RH, W/O Pads Or SHIMS
Part Number: 41001-1PA1A
$289.41 MSRP: $459.14
You Save: $169.73 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-1PA1B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front LH,W/O Pads Or SHIMS
Part Number: 41011-7S000
$345.87 MSRP: $458.38
You Save: $112.51 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-7S010RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2005 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Caliper Assy-Rear RH,W/O Pad & Shim
Part Number: 44001-EZ60A
$234.80 MSRP: $354.92
You Save: $120.12 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Titan Brake-Rear LH
Part Number: 44011-1PA1A
$123.54 MSRP: $256.71
You Save: $133.17 (52%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 44011-1PA1C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-1PA1A
$287.99 MSRP: $459.14
You Save: $171.15 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-1PA1B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan CALIPER Assembly-Rear RH,W/O Pads Or SHIMS
Part Number: 44001-7S000
$247.18 MSRP: $356.77
You Save: $109.59 (31%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim
- Position: Passenger Side
- Replaced by: 44001-7S000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Caliper Assy-Rear LH,W/O Pad & Shim
Part Number: 44011-EZ60A
$234.80 MSRP: $354.92
You Save: $120.12 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | PRO-4X, Platinum, Platinum Reserve, S, SL, SV, SV/Comf | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Titan CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-7S000
$345.87
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-7S010RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2005 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE

Nissan Titan Brake Caliper

If you need any OEM Nissan Titan Brake Caliper, feel free to choose them out of our huge selection of genuine Nissan Titan Brake Caliper. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Titan Brake Caliper Parts Questions & Experts Answers

CALIPER Assembly-Front RH, W/O Pads Or SHIMS
41001-ZC60A
Q: How to remove and install the caliper on Nissan Titan?
A: On Armada models equipped with a rear auto-leveling suspension, turn the ignition key to the OFF position before raising the vehicle. This procedure applies to the front and rear disc brake calipers. To remove, loosen the wheel lug nuts, raise the vehicle and place it securely on jackstands. Block the wheels at the opposite end. Remove the wheel. For front caliper (all models) and rear caliper (Armada models), disconnect the brake hose from the caliper. Discard the old sealing washers. Plug the brake hose immediately to keep contaminants and air out of the brake system and to prevent losing any more brake fluid than is necessary. If you are simply removing the caliper for access to other components, leave the brake hose connected. Remove the caliper mounting bolts and detach the caliper. If the hose is still connected, secure the caliper with wire and don't let it hang by the hose. For rear caliper (Titan models), break loose the brake hose fitting, but don't unscrew it yet. If you're just removing the caliper for access to other components, don't loosen the hose. Remove the caliper mounting bolts, detach the caliper, then unscrew the caliper from the brake hose. If you intend to leave the hose connected, secure the caliper with wire and don't let it hang by the brake hose. For installation, the process is the reverse of removal. Don't forget to use new sealing washers on each side of the brake hose inlet fitting and be sure to tighten the fitting bolt and the caliper mounting bolts to the torque values. For rear caliper (Titan models), install a new sealing washer on the brake hose. Thread the caliper onto the brake hose as far as possible, but don't tighten the hose with a wrench yet. Install the caliper and mounting bolts, tightening the bolts to the torque. Tighten the brake hose securely. Make sure the hose isn't twisted. Finally, bleed the brake system. If the brake hose was not disconnected, bleeding won't be required. Make sure there are no leaks from the hose connections. Test the brakes carefully before returning the vehicle to normal service.