How do you disconnect the ignition switch and Ignition Lock Cylinder and perform the necessary installation procedures on Nissan Versa?

Disconnect the cable from the negative terminal of the battery. Remove the steering column covers and disconnect the electrical connector from the ignition switch by depressing the tab. Remove the screws and pull the switch from the ignition lock cylinder housing, ensuring the hub of the new switch is aligned with the blade on the ignition lock cylinder during installation. The remainder of the installation follows the reverse of the removal procedure, followed by reconnecting the battery and performing the necessary re-learn procedures. For the ignition lock cylinder housing, remove the ignition switch and, on models with an automatic transaxle, detach the shift interlock cable from the ignition lock cylinder housing. Remove the shear-head bolts by drilling through their center and using a screw extractor, then install new shear-head bolts, tightening them until the heads break off. Reconnect the battery and perform the necessary re-learn procedures. Up to four intelligent key transponders can be programmed to the vehicle, and a weak battery in the intelligent key transmitter is a common cause of a no start; testing the battery strength at a parts store is advisable. If the intelligent key is left in the glove box or on the dash, the vehicle may not start. For push-button replacement, remove the left-hand lower trim panel from the instrument panel, release the locking tabs to the NATS antenna amp, and remove the antenna. Press in on the tabs to the ignition start button from the back side of the trim panel and slide the button assembly out. Installation is the reverse of removal. To access the remote keyless entry receiver, remove the glove box, disconnect the electrical connector, and release the locking tab with a small screwdriver to remove the receiver, again following the reverse for installation. In an emergency situation where the vehicle cannot be put into Park, shut it off by holding the ignition start/stop button for more than 2 seconds or pressing the start/stop button repeatedly more than 3 times within 1.5 seconds.

Genuine Nissan Versa Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

55 Ignition Lock Cylinders found

View related parts
Nissan Versa Lock Set-Steering
Part Number: D8700-1HL0A
$229.66 MSRP: $306.22
You Save: $76.56 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Lock Cylinder, Steering Lock
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Lock Set-Steering
Part Number: D8700-EL50A
$390.18 MSRP: $520.23
You Save: $130.05 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Lock Cylinder, Steering Lock
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Versa | Base, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Key Set
Part Number: K9810-9KF0A
$264.38 MSRP: $384.55
You Save: $120.17 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2019 Nissan Versa | Base | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Lock Set-Steering
Part Number: D8700-1HL5A
$184.78 MSRP: $246.37
You Save: $61.59 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Lock Cylinder, Steering Lock
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Key Set
Part Number: K9810-3BA0C
$185.76 MSRP: $270.20
You Save: $84.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Key Set
Part Number: 99810-9KA0A
$88.60 MSRP: $128.87
You Save: $40.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: K9810-9KA0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Key Set
Part Number: K9810-9KS1A
$173.41 MSRP: $252.24
You Save: $78.83 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2015-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Lock Set-Steering
Part Number: D8700-EL60A
$395.95 MSRP: $527.93
You Save: $131.98 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Lock Cylinder, Steering Lock
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Versa | Base, Entry, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Lock Steering
Part Number: D8700-ZW80A
$523.84 MSRP: $698.45
You Save: $174.61 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Set-Steering
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2012 Nissan Versa | Base, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Lock Steering
Part Number: D8700-ZW80B
$405.66 MSRP: $540.88
You Save: $135.22 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Set-Steering
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Versa | Base, Entry, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW80E
$131.28 MSRP: $190.95
You Save: $59.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Versa | S | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW80G
$134.66 MSRP: $195.87
You Save: $61.21 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2011 Nissan Versa | Base, Entry, S | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW80H
$135.31 MSRP: $196.82
You Save: $61.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2011 Nissan Versa | Base, S | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW88A
$135.31 MSRP: $196.82
You Save: $61.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2011 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW85C
$162.48 MSRP: $236.33
You Save: $73.85 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-ZW80F
$163.44 MSRP: $237.73
You Save: $74.29 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Versa | S | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Key Set
Part Number: 99810-EL55A
$172.44 MSRP: $250.82
You Save: $78.38 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Key Set
Part Number: K9810-9KS0A
$181.50 MSRP: $264.00
You Save: $82.50 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2015-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Key Set
Part Number: K9810-3BA5C
$192.19 MSRP: $279.55
You Save: $87.36 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Key Set
Part Number: K9810-3AN0A
$269.09 MSRP: $391.40
You Save: $122.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2014 Nissan Versa | Base, SL | 4 Cyl 1.6L | HR16DE

| Page 1 of 3 |Next >

1-20 of 55 Results

Nissan Versa Ignition Lock Cylinder

If you need any OEM Nissan Versa Ignition Lock Cylinder, feel free to choose them out of our huge selection of genuine Nissan Versa Ignition Lock Cylinder. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Versa Ignition Lock Cylinder Parts Questions & Experts Answers

Key Set
K9810-9KF0A
Q: How do you disconnect the ignition switch and Ignition Lock Cylinder and perform the necessary installation procedures on Nissan Versa?
A: Disconnect the cable from the negative terminal of the battery. Remove the steering column covers and disconnect the electrical connector from the ignition switch by depressing the tab. Remove the screws and pull the switch from the ignition lock cylinder housing, ensuring the hub of the new switch is aligned with the blade on the ignition lock cylinder during installation. The remainder of the installation follows the reverse of the removal procedure, followed by reconnecting the battery and performing the necessary re-learn procedures. For the ignition lock cylinder housing, remove the ignition switch and, on models with an automatic transaxle, detach the shift interlock cable from the ignition lock cylinder housing. Remove the shear-head bolts by drilling through their center and using a screw extractor, then install new shear-head bolts, tightening them until the heads break off. Reconnect the battery and perform the necessary re-learn procedures. Up to four intelligent key transponders can be programmed to the vehicle, and a weak battery in the intelligent key transmitter is a common cause of a no start; testing the battery strength at a parts store is advisable. If the intelligent key is left in the glove box or on the dash, the vehicle may not start. For push-button replacement, remove the left-hand lower trim panel from the instrument panel, release the locking tabs to the NATS Antenna amp, and remove the antenna. Press in on the tabs to the ignition start button from the back side of the trim panel and slide the button assembly out. Installation is the reverse of removal. To access the remote keyless entry receiver, remove the glove box, disconnect the electrical connector, and release the locking tab with a small screwdriver to remove the receiver, again following the reverse for installation. In an emergency situation where the vehicle cannot be put into Park, shut it off by holding the ignition start/stop button for more than 2 seconds or pressing the start/stop button repeatedly more than 3 times within 1.5 seconds.

Related Nissan Versa Parts

Browse by Year