How to check and repack the front hub and wheel bearings on Nissan Xterra?

The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.

Genuine Nissan Xterra Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Wheel Bearings found

View related parts
Nissan Xterra Bearing-Rear Axle Inner
Part Number: 40210-7S210
$73.11 MSRP: $111.20
You Save: $38.09 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Inner,Rear Axle
- Manufacturer Note: M226
- Position: Rear Inner
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2015 Nissan Xterra | S | 6 Cyl 4.0L | VQ40DE
- 2005-2012 Nissan Xterra | Base Camp, Off-Road, S | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Hub Assembly Road Wheel
Part Number: 40202-4X01A
$197.70 MSRP: $300.73
You Save: $103.03 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2015 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Bearing-Needle,Drive Shaft
Part Number: 40588-88G00
$34.72 MSRP: $49.03
You Save: $14.31 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Drive Shaft; Axle Assembly Bearing, Axle Bearing
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER
View related parts
Nissan Xterra Bearing-Rear Axle,Inner
Part Number: 43210-EA200
$109.34 MSRP: $166.32
You Save: $56.98 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Inner,Rear Axle; Bearing
- Manufacturer Note: C200K
- Position: Rear Inner
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2015 Nissan Xterra | Base Camp, Off-Road, S, SE, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Bearing Wheel
Part Number: 40210-85000
$64.70 MSRP: $95.43
You Save: $30.73 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Differential Side
- Replaces: 38440-25660, 40211-85000, 40212-85000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Bearing Assy-Front Wheel
Part Number: 40210-50W00
$65.43 MSRP: $99.52
You Save: $34.09 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Wheel Bearing, Inner Bearing, Wheel Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E, VG33ER
View related parts
Nissan Xterra Bearing ASY Out
Part Number: 40215-50W00
$59.56 MSRP: $87.85
You Save: $28.29 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assy-Front Wheel; Front Wheel Bearing, Outer Bearing, Wheel Bearing
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E, VG33ER
View related parts
Nissan Xterra Bearing-Side Shaft
Part Number: 38440-EA500
$49.13 MSRP: $65.50
You Save: $16.37 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Bearing, Bearing, Output Shaft Bearing
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2015 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Bearing Wheel
Part Number: 43215-H5000
$50.54 MSRP: $74.55
You Save: $24.01 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Side Shaft; Axle Bearing, Bearing, Outer Bearing
- Replaces: 43215-22500, 43125-H5000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER
View related parts
Nissan Xterra Bearing-Rear Axle,Inner
Part Number: 43210-VE000
$77.41 MSRP: $117.75
You Save: $40.34 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Inner,Rear Axle
- Position: Rear Inner
- Replaced by: 43210-0W000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER

Nissan Xterra Wheel Bearing

If you need any OEM Nissan Xterra Wheel Bearing, feel free to choose them out of our huge selection of genuine Nissan Xterra Wheel Bearing. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Xterra Wheel Bearing Parts Questions & Experts Answers

Bearing Wheel
43215-H5000
Q: How to check and repack the front hub and wheel bearings on Nissan Xterra?
A: The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.

Related Nissan Xterra Parts

Browse by Year

2015 Wheel Bearing 2014 Wheel Bearing 2013 Wheel Bearing 2012 Wheel Bearing 2011 Wheel Bearing 2010 Wheel Bearing 2009 Wheel Bearing 2008 Wheel Bearing 2007 Wheel Bearing 2006 Wheel Bearing 2005 Wheel Bearing 2004 Wheel Bearing 2003 Wheel Bearing 2002 Wheel Bearing 2001 Wheel Bearing 2000 Wheel Bearing