Contact Us: Live Chat or 1-888-726-6993
My Garage
My Account
My Cart
Make sure this part fits your vehicle

Nissan 48430-2S403 Steering Wheel Assembly W/O Pad

1998-2000 Nissan 484302S403

Nissan 48430-2S403 Steering Wheel Assembly W/O Pad
  • Part Description
    Wheel Assy-Steering,Less Pad ; Wheel Assy-Steering W/O Pad
  • Lookup Code
    48400M
  • Replaced By
    48430-9Z016
  • Manufacturer
    Nissan
  • Manufacturer's Notes
    This part is discontinued.
Customer Questions & Answers
  • Product Specifications

    BrandGenuine Nissan
    Lookup Code48400M
    Manufacturer Part Number48430-2S403
    Part DescriptionWheel Assy-Steering,Less Pad ; Wheel Assy-Steering W/O Pad
    Item Dimensions18.7 x 16.2 x 6.6 inches
    Item Weight7.20 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerNissan
    SKU48430-2S403
    WarrantyThis genuine Nissan part is guaranteed by Nissan's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    1998-2000 Nissan FrontierSE, STD, XE|4 Cyl 2.4LKA24DE
    2000 Nissan XterraSE|6 Cyl 3.3LVG33E

Customer Questions & Answers

Q:
I would like to verify that part given Posted by NissanPartsDeal Specialist
A:
You can Select Your Vehicle to check if 48430-2S403 fits your vehicle.
Posted by NissanPartsDeal Specialist
Q:
How do I remove the steering wheel on Nissan Frontier? Posted by Customer
A:
Detach the Positive and negative battery terminals, wait for at least ten minutes before removing the steering wheel. After that, detach the little cover below the steering wheel and unplug airbag module connector. Pry off side covers and remove torx bolts behind them. Some versions may have a screw instead of a cover securing the cruise control or stereo control switch. Now, lift out the airbag module from the steering wheel. Turn the steering wheel so that wheels are straight ahead. Remove steering wheel holding nut also note down where it was connected to the shaft of Steering column. Disconnect electrical connector from Cruise Control wiring harness and remove horn connector if it exists. Pull off using a puller ensuring that you do not hammer on shaft but separate a steering wheel from its shaft in case there is need to do this process through detaching screws fastening it to column, disconnecting an electrical connector and unscrewing it off column. When installing align turn signal cancel tab with notch in combination switch or straight ahead front wheels if clock spring had been removed upon installation.Rotate clockwise then counterclockwise until arrow on bottom has aligned with pin on clockspring hub at bottom until clock spring stops moving.Pull wires out of airbag module and cruis control system through that part of steering wheel where they are located to ensure that pin guides ensuring engagement with corresponding holes by use of clockspring are engaged.Plug horn back in if you had untangled it.Install back retaining nut and tighten it.Put back new torx bolts for securing airbag module and replace side covers cruise control switch when applicable.Attach airbag module connector then put lower cover.On engine start, turn extreme left and right to reset clockspring.Run Ignition key into On or Start position to check if "AIR BAG" warning light comes on momentarily.Verify proper functioning of airbag circuit by turning ignition key into "Start" or "ON" position.Key should be turned on or started; as a result, "AIR BAG" warning light should illuminate momentarily before going off.
Posted by NissanPartsDeal Specialist
Q:
What precautions should be taken when reinstalling the clockspring for the 2002 Nissan Xterra? Posted by Customer
A:
When reinstalling the clockspring, make sure the front wheels are straight ahead and align the turn signal cancel tab with the notch in the combination switch if the clockspring was removed.
Posted by NissanPartsDeal Specialist
See expert answers on similar Steering Wheel
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Nissan Part 48430-2S403, the Right Choice

To ensure reliability, purchase Nissan part # 48430-2S403 Steering Wheel Assembly W/O Pad. It is sometimes referred to as Nissan Steering Wheel. OEM parts are the #1 choice in terms of quality. Crafted by Nissan, they follow rigorous factory specs and go through the demanding quality control processes during manufacturing. This part fits 1998-2000 Nissan Frontier, 2000 Nissan Xterra.

NissanPartsDeal.com is a leading supplier of genuine Nissan parts and accessories such as Nissan 484302S403 Steering Wheel Assembly W/O Pad. Welcome to our vast selection of competitively-priced genuine Nissan parts available online. Each OEM Nissan part we provide is backed by a manufacturer's warranty and is subject to a stress-free return policy. Place your order now and receive your parts quickly, shipped directly to your doorstep.

Why choose Nissan Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly