Nissan 26293-C9912 Bulb

You can Select Your Vehicle to check if 26293-C9912 fits your vehicle.

To change the front side marker/turn signal lights, unscrew it and pull the turn signal and side marker light housing off of the fender. Twist the bulb socket out of its housing and push the bulb in. For the tail and back-up lights, open the tailgate on Frontier models or remove the bolts on Xterra and Pathfinder models to pull out taillight housing from bed side or body. With draw bulb socket from its housing and replace a light source. In order to replace license plate light, remove screws securing housing to bumper for Frontier models; snap it off for Xterra models, while lift up screws will help you detach it from bumper on Pathfinder models. Pull out the lamp straightly to replace it. For this high-mounted brake light, take off lenses by undoing screws holding them in place from roof area on Frontier models; open liftgate on Xterra models then unsnap cover from trim panel or lift off screws that hold lens assembly on liftgate on Pathfinder model(s). Simply pull out lamp straightly from socket to change it. To switch instrument cluster illumination lights, detach instrument cluster then twist counterclockwise bulb holder for removing it. For interior lights just pry map lights or dome light lenses off and change their bulbs. Regarding fog lights remove grille that covers lower part of bumper as well as relevant mounting bolts for fog light; extract light itself then unplug electrical connector, release retaining clip and take out bulb(s) from fog light housing. Carefully pry fog lamps away from front bumper fascia if they belong to 1999-2000 Pathfinder cars until you see access path to fog lamp's bulb inside. In case of 1996 through 1998 Pathfinders unscrew holding fastener, withdraw whole lighting assembly after disengagement electrical plug was removed; finally we have tear apart lamp retainer too because our hands did not fit through hole where would be bulb. As regards all other cars, fog light lens clips can be detached from both sides after lens is taken out; then we need to disconnect electrical plug and unfasten retaining spring before removing bulb from such lens. In case of need remove nut that secures fog lamp to retaining bracket.

To change the front side marker/turn signal lights, unscrew it and pull the turn signal and side marker light housing off of the fender. Twist the bulb socket out of its housing and push the bulb in. For the tail and back-up lights, open the tailgate on Frontier models or remove the bolts on Xterra and Pathfinder models to pull out taillight housing from bed side or body. With draw bulb socket from its housing and replace a light source. In order to replace license plate light, remove screws securing housing to bumper for Frontier models; snap it off for Xterra models, while lift up screws will help you detach it from bumper on Pathfinder models. Pull out the lamp straightly to replace it. For this high-mounted brake light, take off lenses by undoing screws holding them in place from roof area on Frontier models; open liftgate on Xterra models then unsnap cover from trim panel or lift off screws that hold lens assembly on liftgate on Pathfinder model(s). Simply pull out lamp straightly from socket to change it. To switch instrument cluster illumination lights, detach instrument cluster then twist counterclockwise bulb holder for removing it. For interior lights just pry map lights or dome light lenses off and change their bulbs. Regarding fog lights remove grille that covers lower part of bumper as well as relevant mounting bolts for fog light; extract light itself then unplug electrical connector, release retaining clip and take out bulb(s) from fog light housing. Carefully pry fog lamps away from front bumper fascia if they belong to 1999-2000 Pathfinder cars until you see access path to fog lamp's bulb inside. In case of 1996 through 1998 Pathfinders unscrew holding fastener, withdraw whole lighting assembly after disengagement electrical plug was removed; finally we have tear apart lamp retainer too because our hands did not fit through hole where would be bulb. As regards all other cars, fog light lens clips can be detached from both sides after lens is taken out; then we need to disconnect electrical plug and unfasten retaining spring before removing bulb from such lens. In case of need remove nut that secures fog lamp to retaining bracket.

To change the front side marker/turn signal lights, unscrew it and pull the turn signal and side marker light housing off of the fender. Twist the bulb socket out of its housing and push the bulb in. For the tail and back-up lights, open the tailgate on Frontier models or remove the bolts on Xterra and Pathfinder models to pull out taillight housing from bed side or body. With draw bulb socket from its housing and replace a light source. In order to replace license plate light, remove screws securing housing to bumper for Frontier models; snap it off for Xterra models, while lift up screws will help you detach it from bumper on Pathfinder models. Pull out the lamp straightly to replace it. For this high-mounted brake light, take off lenses by undoing screws holding them in place from roof area on Frontier models; open liftgate on Xterra models then unsnap cover from trim panel or lift off screws that hold lens assembly on liftgate on Pathfinder model(s). Simply pull out lamp straightly from socket to change it. To switch instrument cluster illumination lights, detach instrument cluster then twist counterclockwise bulb holder for removing it. For interior lights just pry map lights or dome light lenses off and change their bulbs. Regarding fog lights remove grille that covers lower part of bumper as well as relevant mounting bolts for fog light; extract light itself then unplug electrical connector, release retaining clip and take out bulb(s) from fog light housing. Carefully pry fog lamps away from front bumper fascia if they belong to 1999-2000 Pathfinder cars until you see access path to fog lamp's bulb inside. In case of 1996 through 1998 Pathfinders unscrew holding fastener, withdraw whole lighting assembly after disengagement electrical plug was removed; finally we have tear apart lamp retainer too because our hands did not fit through hole where would be bulb. As regards all other cars, fog light lens clips can be detached from both sides after lens is taken out; then we need to disconnect electrical plug and unfasten retaining spring before removing bulb from such lens. In case of need remove nut that secures fog lamp to retaining bracket.