Contact Us: Live Chat or 1-888-726-6993
My Garage
My Account
My Cart
Make sure this part fits your vehicle

Nissan 13020-40F00 Camshaft Assy

1989-1994 Nissan 1302040F00

Nissan 13020-40F00 Camshaft Assy
  • Part Description
    Camshaft Assy
  • Lookup Code
    13020
  • Replaced By
    13020-40F01
  • Manufacturer
    Nissan
  • Manufacturer's Notes
    This part is discontinued.
Customer Questions & Answers
  • Product Specifications

    BrandGenuine Nissan
    Lookup Code13020
    Manufacturer Part Number13020-40F00
    Part DescriptionCamshaft Assy
    Item Dimensions19.4 x 2.1 x 2.1 inches
    Item Weight7.10 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerNissan
    SKU13020-40F00
    WarrantyThis genuine Nissan part is guaranteed by Nissan's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    1989-1991 Nissan 240SX4 Cyl 2.4LKA24E
    1989-1994 Nissan Hardbody Pickup (D21)DX|4 Cyl 2.4LKA24E

Customer Questions & Answers

Q:
Will this part fit my car? Posted by NissanPartsDeal Specialist
A:
You can Select Your Vehicle to check if 13020-40F00 fits your vehicle.
Posted by NissanPartsDeal Specialist
Q:
How to perform an overhaul on engines without replaceable camshaft bearings on Nissan 240sx? Posted by Customer
A:
To overhaul engines like CA20E, VG30E and CASeries whose camshaft bearings cannot be changed,start by removing the sprocket of the camshaft and timing chain to ensure that number one piston is at TDC on compression stroke. Proceed to loosen (remove) bolts that secure the rocker shaft assembly but do not remove the four end bolts which hold it together as a unit. Gradually loosen all bolts a little at a time so as not to put excessive strain on the camshaft or rocker assembly. Thereafter, remove the rocker assembly and carefully push out the camshaft through front of vehicle keeping track of disassembled parts in order. When dissembling rocker unit, join again through mounting brackets, valve rockers, springs with correct identification from instructions. Then inspect the camshaft runout, end play, wear and journal clearance. Apply sealant on each saddle before putting on top part of cylinder head with dowel pin up for installing. Place the rocker assembly onto the head making sure it goes over the knock pin and torque down in stages moving inwards and outwards from center both sides 11-18ft.lbs. Make sure when you are installing this engine is at TDC of compression stroke for No.1 piston to prevent valve damage. At last adjust valves. For CASeries engines in 200 SX & Stanza follow these steps: disconnect negative battery cable, set no1 piston TDC of compression stroke and remove timing belt plus valve rocker cover then go ahead to loosen all rocker arm adjusting screws plus rocker shaft mounting bolts gradually remove them as an assembly keeping components arranged in order respectively (in order). After removing camshaft pulley then thrust plate carefully pry out oil seal for camshaft slide it outside cylinder head without scoring journals (do not score journals). Apply clean engine oil coat to camshaft its back into cylinder head bushing sliding thus installing it. Install a new oil seal and thrust plate, torquing the thrust plate bolt to 58-65 ft. lbs. Apply clean engine oil on rocker shafts; insert bracket bolts for spring slippage, and gradually tighten rocker shaft bolts to 13-16 ft.lbs in stages. Reinstall camshaft pulley followed by timing belt,assured that valves being adjusted and connecting battery's negative cable eventually cylinder head cover is replaced.battery is connected before installing cylinder head cover. In order to access camshaft for removal or installation, disconnect negative battery cable, drain the cooling system and take off: timing belt, collector assembly and intake manifold on 200SX with VG30E engine.
Posted by NissanPartsDeal Specialist
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Nissan Part 13020-40F00, the Right Choice

To ensure reliability, purchase Nissan part # 13020-40F00 Camshaft Assy. It is sometimes referred to as Nissan Camshaft. OEM parts are the #1 choice in terms of quality. Crafted by Nissan, they follow rigorous factory specs and go through the demanding quality control processes during manufacturing. This part fits 1989-1991 Nissan 240SX, 1989-1994 Nissan Hardbody Pickup (D21).

NissanPartsDeal.com is a leading supplier of genuine Nissan parts and accessories such as Nissan 1302040F00 Camshaft Assy. Welcome to our vast selection of competitively-priced genuine Nissan parts available online. Each OEM Nissan part we provide is backed by a manufacturer's warranty and is subject to a stress-free return policy. Place your order now and receive your parts quickly, shipped directly to your doorstep.

Why choose Nissan Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly