How do you remove and reinstall the rear axle assembly and associated components from a Nissan Juke?

Chock the front wheels, jack up the rear of the car, and support it on axle stands before removing both rear roadwheels. Unscrew the brake master cylinder fluid reservoir cap and place it on a piece of polythene to minimize fluid loss. Undo the bolt securing the ABS wheel speed sensor to the hub/stub axle assembly on each side, withdraw the sensors, and unclip the sensor wiring from the rear axle. Remove the handbrake shoes from inside the rear brake discs, unbolt the handbrake cables, and withdraw them from the lower part of the brake backplate. Undo the support bracket retaining bolts and release the handbrake cables from their attachments on the rear axle. Slacken the union nuts and disconnect the brake pipes from the flexible hose unions on the rear axle, plugging the pipe and hose ends to minimize fluid loss and prevent dirt entry into the hydraulic system. Remove the retaining clips and release the two flexible hoses from their mounting brackets, then remove the rear coil springs. Support the weight of the axle assembly using two trolley jacks or one trolley jack with a length of wood, requiring assistance. Undo the four bolts on each side securing the axle front mounting brackets to the underbody, then check that all necessary components have been disconnected and positioned to avoid hindrance during removal. Carefully lower the axle assembly out of position and remove it from underneath the vehicle, allowing for the removal of brake components and hub bearing units. If necessary, remove the front mounting brackets by unscrewing the retaining nut and withdrawing the centre through-bolt, noting that new through-bolt retaining nuts will be required for reassembly. Refit any components removed from the axle as applicable, and if the front mounting brackets were removed, refit them and lightly tighten the new through-bolt nuts. Support the axle on trolley jacks and position the assembly under the rear of the vehicle, then raise the jacks and lightly tighten the front mounting bracket retaining bolts. With all bolts in place, work progressively in a diagonal sequence to tighten all bolts to the specified torque, then refit the rear coil springs. Refit the brake hydraulic pipes and flexible hoses along with the retaining clips, tightening the union nuts securely. Reconnect the handbrake cables to the brake backplates and underbody supports, then refit the handbrake shoes and rear brake discs. Refit the ABS wheel speed sensors, tightening the retaining bolts to the specified torque, bleed the complete brake hydraulic system, and adjust the handbrake. Finally, refit the roadwheels and lower the vehicle to the ground, ensuring that with the vehicle on its wheels at normal ride height, the new front mounting bracket through-bolt nuts are tightened to the specified torque.

Genuine Nissan Juke Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Axle Shafts found

View related parts
Nissan Juke Shaft Assembly-Front Drive RH
Part Number: 39100-1KB0A
$490.92 MSRP: $752.63
You Save: $261.71 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-BV81E
$670.62 MSRP: $1028.13
You Save: $357.51 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver side
- Replaces: 39101-BV81C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2017 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assembly-Front Drive RH
Part Number: 39100-1KB5B
$495.97 MSRP: $723.20
You Save: $227.23 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-1KD0A
$500.82 MSRP: $767.82
You Save: $267.00 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH
- Position: Driver side
- Replaced by: 39101-1KD0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2016 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Drive Shaft Rear RH
Part Number: 39600-1KD0A
$783.80 MSRP: $1201.65
You Save: $417.85 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Rear Drive
- Position: Rear Passenger Side
- Replaced by: 39600-1KD0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assembly-Front Drive RH
Part Number: 39100-1KD0A
$497.51 MSRP: $762.73
You Save: $265.22 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Position: Passenger Side
- Replaced by: 39100-1KD0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2016 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-1KB0A
$522.99 MSRP: $801.80
You Save: $278.81 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assembly-Front Drive RH
Part Number: 39100-3YV0B
$529.10 MSRP: $1027.57
You Save: $498.47 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH. This item is non-returnable.; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assy-Front Drive,RH
Part Number: 39100-BV81E
$539.65 MSRP: $827.33
You Save: $287.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 39100-BV81C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2017 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-3YV0B
$667.72 MSRP: $1023.68
You Save: $355.96 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-1KB5B
$494.83 MSRP: $758.63
You Save: $263.80 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assembly-Front Drive RH
Part Number: 39100-1KD0B
$497.51 MSRP: $762.73
You Save: $265.22 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Replaces: 39100-1KD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assy-Front Drive,RH
Part Number: 39100-BV81C
$539.65 MSRP: $827.33
You Save: $287.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: 39100-BV81E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2016 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Assy-Front Drive,LH
Part Number: 39101-BV81C
$670.62 MSRP: $1028.13
You Save: $357.51 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver side
- Replaced by: 39101-BV81E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2016 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft-Front Drive,RH
Part Number: 39204-BV81C
$179.12 MSRP: $287.42
You Save: $108.30 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Front Drive,RH. This item subject to a 40% restocking fee if returned.
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2017 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft Front Drive
Part Number: 39101-1KD0B
$500.82 MSRP: $767.82
You Save: $267.00 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver side
- Replaces: 39101-1KD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft-Front Drive,RH
Part Number: 39204-1KD0A
$207.13 MSRP: $276.17
You Save: $69.04 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft-Front Drive,RH
Part Number: 39204-1KB0A
$222.33 MSRP: $296.43
You Save: $74.10 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft-Front Drive,RH
Part Number: 39204-3YV0B
$263.93 MSRP: $351.90
You Save: $87.97 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Shaft-Front Drive,RH
Part Number: 39204-1KB5B
$207.13 MSRP: $276.17
You Save: $69.04 (25%)
Product Specifications
- Other Name: Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT

Nissan Juke Axle Shaft

If you need any OEM Nissan Juke Axle Shaft, feel free to choose them out of our huge selection of genuine Nissan Juke Axle Shaft. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Juke Axle Shaft Parts Questions & Experts Answers

Drive Shaft Rear RH
39600-1KD0A
Q: How do you remove and reinstall the rear axle assembly and associated components from a Nissan Juke?
A: Chock the front wheels, jack up the rear of the car, and support it on axle stands before removing both rear roadwheels. Unscrew the brake master cylinder fluid reservoir cap and place it on a piece of polythene to minimize fluid loss. Undo the bolt securing the ABS wheel speed sensor to the hub/stub axle assembly on each side, withdraw the sensors, and unclip the sensor wiring from the rear axle. Remove the handbrake shoes from inside the rear brake discs, unbolt the handbrake cables, and withdraw them from the lower part of the brake backplate. Undo the support bracket retaining bolts and release the handbrake cables from their attachments on the rear axle. Slacken the union nuts and disconnect the brake pipes from the flexible hose unions on the rear axle, plugging the pipe and hose ends to minimize fluid loss and prevent dirt entry into the hydraulic system. Remove the retaining clips and release the two flexible hoses from their mounting brackets, then remove the rear Coil Springs. Support the weight of the axle assembly using two trolley jacks or one trolley jack with a length of wood, requiring assistance. Undo the four bolts on each side securing the axle front mounting brackets to the underbody, then check that all necessary components have been disconnected and positioned to avoid hindrance during removal. Carefully lower the axle assembly out of position and remove it from underneath the vehicle, allowing for the removal of brake components and hub bearing units. If necessary, remove the front mounting brackets by unscrewing the retaining nut and withdrawing the centre through-bolt, noting that new through-bolt retaining nuts will be required for reassembly. Refit any components removed from the axle as applicable, and if the front mounting brackets were removed, refit them and lightly tighten the new through-bolt nuts. Support the axle on trolley jacks and position the assembly under the rear of the vehicle, then raise the jacks and lightly tighten the front mounting bracket retaining bolts. With all bolts in place, work progressively in a diagonal sequence to tighten all bolts to the specified torque, then refit the rear coil springs. Refit the brake hydraulic pipes and flexible hoses along with the retaining clips, tightening the union nuts securely. Reconnect the handbrake cables to the brake backplates and underbody supports, then refit the handbrake shoes and rear brake discs. Refit the ABS wheel speed sensors, tightening the retaining bolts to the specified torque, bleed the complete brake hydraulic system, and adjust the handbrake. Finally, refit the roadwheels and lower the vehicle to the ground, ensuring that with the vehicle on its wheels at normal ride height, the new front mounting bracket through-bolt nuts are tightened to the specified torque.

Related Nissan Juke Parts

Browse by Year

2017 Axle Shaft 2016 Axle Shaft 2015 Axle Shaft 2014 Axle Shaft 2013 Axle Shaft 2012 Axle Shaft 2011 Axle Shaft