How do you inspect and renew 1.2L petrol Nissan Juke mountings?

To assess the brakes, make sure that the handbrake is on before jacking up the front part of the car and placing it on the axle stands. At the base of the mounting check the rubber for signs of cracking, hardening or if the rubber has separated from the metal, if there is any evidence to suggest that the rubber needs replacement, then then it should be replace by a new one. Tighten all fasteners to the appropriate level, if a torque wrench is available use it. A visible examination and an attempt to lever against the mounting should be made; If there is too much of free play, one should look at the fasteners and determine whether they are still tight or not and replace any worn out bearings. In the case of the right-hand mounting, the following procedures were taken; disconnect the battery negative terminal, jack up the engine with wood block support, removed the retaining bolt from the inner wing panel and engine mounting bracket and finally withdrew the complete mounting. Check and replace any worn or damaged part of the widget as and when needed. Loosen and remove the engine mounting and bracket and replace it then tightened the bolts and then slowly lower the jack and connect the battery. To replace left hand mounting pull out the battery and tray, lift up with jack the transmission and unscrew the nuts to pull out the mounting. If required, it is disengaged upper and lower mounting brackets, and that it is checked for wear or damage on this and renew certain parts of it. Replace the brackets back and fasten the retaining bolts properly in their respective positions, touching the lower bracket bolt to the left hand rubber mounting and fasten the nut. Replace the outer retaining nuts, remove the jack, replace the battery along with the tray. For the rear lower mounting one should use handbrake ,jack up the front of the car and secure it firmly. Unfasten all the bolts, which united the rear mounting bracket to the transmission, and take it out, then, unfasten the bolt, which united the rear mounting link to the subframe. Check for the levels of tear and wear and replace all the components that appear damaged. Reassemble by screwing the rear mounting into its place on the subframe and then tightening the retaining bolt followed by the mounting bracket into the transmission and fastening the bolts. Lastly, lower the vehicle back down to the ground to its recommended standard height.

Genuine Nissan Juke Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Motor And Transmission Mounts found

View related parts
Nissan Juke Rod Assy-Torque
Part Number: 11360-1KA0A
$122.73 MSRP: $163.63
You Save: $40.90 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Mount, Strut, Torque Rod
- Replaced by: 11360-5US0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator Left
Part Number: 11220-1KG0A
$95.47 MSRP: $145.23
You Save: $49.76 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH; Mount, Side Mount
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator, Right
Part Number: 11210-1KC0B
$127.52 MSRP: $193.98
You Save: $66.46 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,Rh; Mount, Side Mount
- Position: Passenger Side
- Replaces: 11210-1KC0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2015 Nissan Juke | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator ,Left
Part Number: 11220-4BB0A
$109.99 MSRP: $167.32
You Save: $57.33 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH; Mount, Side Mount
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Support, Left
Part Number: 11254-1KG0A
$325.10 MSRP: $433.47
You Save: $108.37 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket Engine ; Support-Engine Mounting,Lh; Side Mount Support Bracket, Side Support
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Bracket, Rear
Part Number: 11332-1KC0B
$147.29 MSRP: $196.38
You Save: $49.09 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mounting,Rear; Torque Rod Bracket
- Position: Rear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator Left
Part Number: 11220-1KF2A
$164.57 MSRP: $250.33
You Save: $85.76 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH
- Position: Driver side
- Replaced by: 11220-1KF2B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2013 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator, Right
Part Number: 11210-1KC0C
$214.99 MSRP: $327.02
You Save: $112.03 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,Rh; Mount, Side Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator, Left
Part Number: 11220-1KF2B
$164.57 MSRP: $250.33
You Save: $85.76 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH; Mount, Side Mount
- Position: Driver side
- Replaces: 11220-1KF2A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator ,Front Left
Part Number: 11220-1KF1C
$213.01 MSRP: $324.02
You Save: $111.01 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assy-Engine Mounting,Front Lh ; Insulator-Engine Mounting,Lh; Mount, Side Mount
- Position: Driver side
- Replaces: 11220-1KF1A, 11220-1KF1B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator, Left
Part Number: 11220-1KF1B
$213.01 MSRP: $324.02
You Save: $111.01 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH
- Position: Driver side
- Replaced by: 11220-1KF1C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2016 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Bracket, Rear
Part Number: 11332-1KD0A
$50.76 MSRP: $67.68
You Save: $16.92 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mounting,Rear; Torque Rod Bracket
- Position: Rear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Rear Engine Mount Bracket
Part Number: 11332-1KC0A
$83.95 MSRP: $111.93
You Save: $27.98 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mounting,Rear; Torque Rod Bracket
- Position: Rear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2012 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator ,Right
Part Number: 11210-3PT0A
$184.69 MSRP: $280.93
You Save: $96.24 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,Rh; Side Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Juke | Base, Luxury, Nismo, Nismors, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Insulator Left
Part Number: 11220-1KF1A
$213.01 MSRP: $324.02
You Save: $111.01 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator-Engine Mounting,LH
- Position: Driver side
- Replaced by: 11220-1KF1C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2013 Nissan Juke | Base, Luxury, S, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Bracket, Left
Part Number: 11253-3YW0A
$147.08 MSRP: $196.10
You Save: $49.02 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mounting,LH; Side Mount Bracket
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Support, Left
Part Number: 11254-3YW0A
$348.01 MSRP: $464.02
You Save: $116.01 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket Engine ; Support-Engine Mounting,Lh; Side Mount Support Bracket
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Juke | Nismo, Nismors | 4 Cyl 1.6L | MR16DDT
View related parts
Nissan Juke Engine Mounting Bracket, Left
Part Number: 11253-1KG0A
$103.71 MSRP: $138.28
You Save: $34.57 (25%)
Product Specifications
- Other Name: Bracket-Engine Mounting,LH; Side Mount Bracket
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Juke | Luxury, Nismo, SL, SV, Upper | 4 Cyl 1.6L | MR16DDT

Nissan Juke Motor And Transmission Mount

If you need any OEM Nissan Juke Motor And Transmission Mount, feel free to choose them out of our huge selection of genuine Nissan Juke Motor And Transmission Mount. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Juke Motor And Transmission Mount Parts Questions & Experts Answers

Engine Mounting Insulator, Right
11210-1KC0B
Q: How do you inspect and renew 1.2L petrol Nissan Juke mountings?
A: To assess the brakes, make sure that the handbrake is on before jacking up the front part of the car and placing it on the axle stands. At the base of the mounting check the rubber for signs of cracking, hardening or if the rubber has separated from the metal, if there is any evidence to suggest that the rubber needs replacement, then then it should be replace by a new one. Tighten all fasteners to the appropriate level, if a torque wrench is available use it. A visible examination and an attempt to lever against the mounting should be made; If there is too much of free play, one should look at the fasteners and determine whether they are still tight or not and replace any worn out bearings. In the case of the right-hand mounting, the following procedures were taken; disconnect the battery negative terminal, jack up the engine with wood block support, removed the retaining bolt from the inner wing panel and engine mounting bracket and finally withdrew the complete mounting. Check and replace any worn or damaged part of the widget as and when needed. Loosen and remove the engine mounting and bracket and replace it then tightened the bolts and then slowly lower the jack and connect the battery. To replace left hand mounting pull out the battery and tray, lift up with jack the transmission and unscrew the nuts to pull out the mounting. If required, it is disengaged upper and lower mounting brackets, and that it is checked for wear or damage on this and renew certain parts of it. Replace the brackets back and fasten the retaining bolts properly in their respective positions, touching the lower bracket bolt to the left hand rubber mounting and fasten the nut. Replace the outer retaining nuts, remove the jack, replace the battery along with the tray. For the rear lower mounting one should use handbrake ,jack up the front of the car and secure it firmly. Unfasten all the bolts, which united the rear mounting bracket to the transmission, and take it out, then, unfasten the bolt, which united the rear mounting link to the subframe. Check for the levels of tear and wear and replace all the components that appear damaged. Reassemble by screwing the rear mounting into its place on the subframe and then tightening the retaining bolt followed by the mounting bracket into the transmission and fastening the bolts. Lastly, lower the vehicle back down to the ground to its recommended standard height.

Related Nissan Juke Parts

Browse by Year

2017 Motor And Transmission Mount 2016 Motor And Transmission Mount 2015 Motor And Transmission Mount 2014 Motor And Transmission Mount 2013 Motor And Transmission Mount 2012 Motor And Transmission Mount 2011 Motor And Transmission Mount