How to remove and install a radiator and Coolant Reservoir in a Nissan Murano?

Disconnect the cable from the negative terminal of the battery. Drain the cooling system. Raise the vehicle and support it securely on jackstands. Remove the lower engine splash shield, the air inlet duct, and the radiator top covers. Remove the grille and the hood latch assembly. Remove the horn. Disconnect the coolant reservoir hose from the radiator cap adapter. Disconnect the transaxle cooler hoses from the radiator. Remove the upper radiator hose including the cap and adapter. Disconnect the lower radiator hose from the radiator. Detach the upper radiator mounts by spreading the horseshoe clips to release the rubber bushings. Pull the top of the radiator back and upward to lift it out. With the radiator removed, it can be inspected for leaks and damage. If it needs repair, have a radiator shop or dealer service department perform the work, as special techniques are required. Bugs and dirt can be removed from the radiator with a soft brush, followed by forcing water from a garden hose through the core from the engine side. Don't bend the cooling fins as this is done. Installation is the reverse of the removal procedure. Be sure the radiator mounting pads are seated properly at the base of the radiator. After installation, fill the cooling system with the proper mixture of antifreeze and water. Reconnect the battery and perform the necessary re-learn procedures. Allow the engine to reach normal operating temperature, indicated by the upper radiator hose becoming hot. Recheck the coolant level and add more if required. Check and add transmission fluid as needed. Disconnect the overflow hose from the fitting by the radiator cap. Unbolt the coolant reservoir and remove it from the vehicle. Pour the coolant into a container. Wash out the reservoir, using soapy water and a long brush to make the coolant level easier to read. Inspect the reservoir for cracks and chafing. Replace it if any damage is found. Installation is the reverse of removal.

Genuine Nissan Murano Coolant Reservoir

Coolant Tank Reservoir

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Coolant Reservoirs found

View related parts
Nissan Murano Tank Assy-Reserve
Part Number: 21710-JP10A
$98.21 MSRP: $130.95
You Save: $32.74 (25%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Tank Assy-Radiator Reservoir; Reservoir Tank
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Tank Assy-Radiator Reservoir
Part Number: 21710-5BC0A
$175.13 MSRP: $233.50
You Save: $58.37 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir, Reservoir Tank
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2015-2024 Nissan Murano | Midnight Edition, Platinum, S, SL, SV | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Tank Assy-Reserve
Part Number: 21710-CA000
$126.65 MSRP: $168.87
You Save: $42.22 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank Assy-Radiator Reservoir
- Replaced by: 21710-CA00B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2007 Nissan Murano | S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Tank Assy-Radiator Reservoir
Part Number: 21710-5AF0A
$138.50 MSRP: $184.67
You Save: $46.17 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Reservoir
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Murano | Platinum, SL, SV | 4 Cyl 2.5L | QR25DER
View related parts
Nissan Murano Tank Kit-Radiator Lower
Part Number: 21463-1AA0A
$210.45 MSRP: $280.60
You Save: $70.15 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank-Radiator,LH W/Oil Cooler; Tank
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Tank Complete-Inverter Cooling Reservoir
Part Number: 21710-3JV0A
$131.05 MSRP: $174.73
You Save: $43.68 (25%)
Product Specifications
- Other Name: Expansion Tank, Reservoir
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Murano | Platinum, SL, SV | 4 Cyl 2.5L | QR25DER
View related parts
Nissan Murano Tank-Radiator,Upper
Part Number: 21412-1AV0A
Product Specifications
- Other Name: Tank
- Position: Upper
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2011 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Hose-Drain
Part Number: 21463-1AV0A
Product Specifications
- Other Name: Tank-Radiator,LH W/Oil Cooler; Tank
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2011 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Tank-Radiator,Upper
Part Number: 21412-1AA0A
$127.21 MSRP: $169.62
You Save: $42.41 (25%)
Product Specifications
- Other Name: Tank
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE

Nissan Murano Coolant Reservoir

Being an essential component of Nissan Murano, Coolant Reservoir or Coolant Recovery Tank offers a critical function in the cooling system of the car. It protects the compact automotive from the infiltration of air in the system hence avoiding leaks of coolants and corrosion of the cooling components. The coolant reservoir comes in two types: screw and snap, the screw type includes pressurized and non-pressurized which are differentiated by the cap. The metal 'TW' cap is also labeled with pressure rating while the unpressurized is capped with a plastic cover. Inspection should be done frequently to spot any crack, leaking or any signs of discoloration as a result of old age or contaminated coolant. Maintenance of the Coolant Reservoir is a very critical aspect of the condition and the efficiency of the Nissan Murano.

If you need any OEM Nissan Murano Coolant Reservoir, feel free to choose them out of our huge selection of genuine Nissan Murano Coolant Reservoir. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Murano Coolant Reservoir Parts Questions & Experts Answers

Tank Assy-Reserve
21710-CA000
Q: How to remove and install a radiator and Coolant Reservoir in a Nissan Murano?
A: Disconnect the cable from the negative terminal of the battery. Drain the cooling system. Raise the vehicle and support it securely on jackstands. Remove the lower engine splash shield, the air inlet duct, and the radiator top covers. Remove the grille and the hood latch assembly. Remove the horn. Disconnect the coolant reservoir hose from the radiator cap adapter. Disconnect the transaxle cooler hoses from the radiator. Remove the upper radiator hose including the cap and adapter. Disconnect the lower radiator hose from the radiator. Detach the upper radiator mounts by spreading the horseshoe clips to release the rubber bushings. Pull the top of the radiator back and upward to lift it out. With the radiator removed, it can be inspected for leaks and damage. If it needs repair, have a radiator shop or dealer service department perform the work, as special techniques are required. Bugs and dirt can be removed from the radiator with a soft brush, followed by forcing water from a garden hose through the core from the engine side. Don't bend the cooling fins as this is done. Installation is the reverse of the removal procedure. Be sure the radiator mounting pads are seated properly at the base of the radiator. After installation, fill the cooling system with the proper mixture of antifreeze and water. Reconnect the battery and perform the necessary re-learn procedures. Allow the engine to reach normal operating temperature, indicated by the upper radiator hose becoming hot. Recheck the coolant level and add more if required. Check and add transmission fluid as needed. Disconnect the overflow hose from the fitting by the radiator cap. Unbolt the coolant reservoir and remove it from the vehicle. Pour the coolant into a container. Wash out the reservoir, using soapy water and a long brush to make the coolant level easier to read. Inspect the reservoir for cracks and chafing. Replace it if any damage is found. Installation is the reverse of removal.