×
- Live Chat
- 1-888-726-6993
My Garage
My Account
Cart
Genuine Nissan Xterra Wheel Hub
Wheel Axle Hub- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
12 Wheel Hubs found
Nissan Xterra Hub Assembly Road Wheel
Part Number: 40202-4X01A$197.70 MSRP: $300.73You Save: $103.03 (35%)Ships in 1-2 Business Days
Nissan Xterra Hub Assembly-Road Wheel,Front
Part Number: 40202-EA300$197.70 MSRP: $300.73You Save: $103.03 (35%)Ships in 1-2 Business Days
Nissan Xterra Hub Assembly-Road Wheel,Front
Part Number: 40202-EA000$246.39 MSRP: $374.80You Save: $128.41 (35%)Ships in 1-3 Business Days
Nissan Xterra Hub Assembly Road Wheel
Part Number: 40202-4X00A$147.22 MSRP: $374.80You Save: $227.58 (61%)Ships in 1-3 Business Days
Nissan Xterra Hub Assembly-Road Wheel,Front
Part Number: 40202-ZP90A$197.70 MSRP: $300.73You Save: $103.03 (35%)Ships in 1-3 Business Days
Nissan Xterra Hub Assembly-Road Wheel,Front
Part Number: 40202-ZP50A$246.39 MSRP: $374.80You Save: $128.41 (35%)Ships in 1-3 Business Days
Nissan Xterra Wheel Hub
If you need any OEM Nissan Xterra Wheel Hub, feel free to choose them out of our huge selection of genuine Nissan Xterra Wheel Hub. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.
Nissan Xterra Wheel Hub Parts Questions & Experts Answers
- Q: How to check and repack the front hub and wheel bearings on Nissan Xterra?A: The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.
