Contact Us: Live Chat or 1-888-726-6993
My Garage
My Account
My Cart
Make sure this part fits your vehicle

Nissan 21010-AL526 Pump Assembly - Water

2001-2003 Nissan 21010AL526

Nissan 21010-AL526 Pump Assembly - Water
  • Part Description
    Pump Assy-Water
  • Lookup Code
    21010
  • Replaced By
    B1010-AL50B
  • Manufacturer
    Nissan
Customer Questions & Answers
$129.57 MSRP: $197.10
You Save: $67.53 (35%)
1
ADD TO CART
Ships in 1-3 Business Days
  • Product Specifications

    BrandGenuine Nissan
    Lookup Code21010
    Manufacturer Part Number21010-AL526
    Part DescriptionPump Assy-Water
    Item Dimensions4.7 x 4.2 x 4.1 inches
    Item Weight2.50 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerNissan
    SKU21010-AL526
    WarrantyThis genuine Nissan part is guaranteed by Nissan's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    2003 Nissan 350ZBase, Enthusiast|6 Cyl 3.5LVQ35DE
    2002-2003 Nissan AltimaSE|6 Cyl 3.5LVQ35DE
    2001-2003 Nissan MaximaGLE, GXEL, SEL, SES|6 Cyl 3.5LVQ35DE
    2003 Nissan MuranoS, SE, SL|6 Cyl 3.5LVQ35DE

Customer Questions & Answers

Q:
Does this part fit my vehicle? Posted by NissanPartsDeal Specialist
A:
You can Select Your Vehicle to check if 21010-AL526 fits your vehicle.
Posted by NissanPartsDeal Specialist
Q:
How to remove and replace a water pump in a Nissan Murano? Posted by Customer
A:
Disconnect the cable from the negative terminal of the battery. Drain the cooling system. If the coolant is relatively new or in good condition, save it for reuse. Loosen the right-front wheel lug nuts, raise the vehicle, and support it securely on jackstands. Remove the right front wheel and the inner fender splash shield. Remove the inlet air duct and the engine lower splash shield. Set the engine to TDC on the compression stroke for cylinder no. Make sure the pointer aligns with the TDC mark on the crankshaft pulley and that the engine is on the compression stroke. Remove the drivebelt. Remove the belt idler pulley and the air conditioning idler pulley. Remove the coolant reservoir. Unbolt the power steering fluid reservoir and set it aside with the lines attached. Place a floor jack under the oil pan using a block of wood as a pad. Raise the jack to take weight off the engine mounts. Remove the right engine mount assembly and the torque rod. Remove the coolant drain plug from the water pump side of the engine block. Disconnect the wiring from the front IVT control valve. Remove the front IVT control valve cover. Remove the chain tensioner cover and the water pump cover from the engine front cover. Push the tensioner plunger in and lock it in the retracted position. Carefully rotate the crankshaft pulley clockwise until the timing chain becomes somewhat loose on the tensioner side, then remove the tensioner. Remove the water pump mounting bolts. Turn the crankshaft counterclockwise (no more than 20 degrees) until the chain becomes slack on the water pump sprocket. Install two 8 mm bolts into the water pump bolt holes and tighten them equally until they bottom against the timing chain cover. Remove the water pump. Clean the sealant from the mating surface and replace the O-rings. Install the O-rings with the white paint mark into the groove closest to the pump flange and the second O-ring into its groove. Apply a light amount of oil to the O-rings. Tighten the pump bolts to the torque. Installation is the reverse of removal. Refill the cooling system, reconnect the battery, and perform the necessary re-learn procedures.
Posted by NissanPartsDeal Specialist
Q:
How should the procedure be finalized for the 2003 Nissan 350Z? Posted by Customer
A:
Refill and bleed the cooling system, run the engine, and check for leaks and proper operation. Allow at least one hour for the sealant to cure.
Posted by NissanPartsDeal Specialist
See expert answers on similar Water Pump
Q:
What steps follow the water pump installation for the 1994 Nissan Maxima? Posted by Customer
A:
All parts removed for access to the pump are reinstalled, the cooling system is refilled and bled, and drivebelt tension is checked. The engine is run, and any leaks are monitored.
Posted by NissanPartsDeal Specialist
See expert answers on similar Water Pump
Q:
Is there a reliable way to determine if the water pump needs replacement without removing it for the 2008 Nissan 350Z? Posted by Customer
A:
Even if the water pump doesn't show obvious signs of trouble, a definitive assessment can only be made by removing it for a close examination.
Posted by NissanPartsDeal Specialist
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Nissan Part 21010-AL526, the Right Choice

To ensure reliability, purchase Nissan part # 21010-AL526 Pump Assembly - Water. It is sometimes referred to as Nissan Water Pump. OEM parts are the #1 choice in terms of quality. Crafted by Nissan, they follow rigorous factory specs and go through the demanding quality control processes during manufacturing. This part fits 2003 Nissan 350Z, 2002-2003 Nissan Altima, 2001-2003 Nissan Maxima, 2003 Nissan Murano.

NissanPartsDeal.com is a leading supplier of genuine Nissan parts and accessories such as Nissan 21010AL526 Pump Assembly - Water. Welcome to our vast selection of competitively-priced genuine Nissan parts available online. Each OEM Nissan part we provide is backed by a manufacturer's warranty and is subject to a stress-free return policy. Place your order now and receive your parts quickly, shipped directly to your doorstep.

Why choose Nissan Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly