How to remove and install lower control arms on Nissan Frontier?

To avoid mistakes and properly remove and install lower control arms on a two-wheel drive Frontier and two-wheel Xterra models,Firstly, loosen wheel lug nuts, lift a vehicle, and support it with jack stands placed under the frame rails. Take off the wheel then remove torsion bar and torque arm. At this moment you can separate stabilizer bar link from lower control arm. Later remove shock absorbers lower mounting bolt. In case of 2WD Frontier models, release tension rod from the bottom arm. To get your lower control arm off steering knuckle, slightly loose balljoint nut before using balljoint separator to relieve balljoint from knuckle. Then take out nut. Thereafter, you can proceed to remove the lower control arm pivot bolt(s) and nut(s) by watching the way they were facing when these steps are done lower control arm could be removed for replacement if necessary. Finally reinstalling is in reverse order of removal except ensuring proper tightening of nuts and bolts or wheel lug nuts as well as alignment checks as outlined in instructions For 4WD Frontier and 4WD Xterra models: Start by loosening wheel lug nuts; raise vehicle and secure with jackstands under frame rails; remove wheel; then remove locking hub assembly along with snap-ring from driveaxle; next take out torsion bar along with torque arm; undo stabilizer bar link from the low control arm; finally unbolt shock absorber low mounting bolt. Unbolt driveaxle inner CV joint from differential drive flange. Remove lower control arm pivot bolts/nuts, separate lower control arm from frame brackets, support driveaxle to prevent it from hanging by outer CV joint. Gently tap end of driveaxle with soft face hammer to disengage driveaxle from hub splines, then pull out axle shaft assembly.; remove cotter pin then back-off (but do not remove) nut from lower ball joint; employ a two-jaw puller to free the ball-stud from steering knuckle; and finally turn off nuts and disconnect lower control arm from steering knuckle. Inspect bushings for wear, hardening, or cracks if found replace bushings. Finally reinstalling is in reverse order of removal except ensuring proper tightening of nuts and bolts or wheel lug nuts as well as torque values for the driveaxle inner flange bolts and the locking hub bolts. For Pathfinder models: Start by loosening wheel lug nuts; raise vehicle and support with jackstands beneath subframe rails; remove wheel; then remove balljoint-to-lower control arm nuts (on Pathfinder models, you can unbolt the balljoint from the control arm by removing the three nuts). Pull up on balljoint to separate it from control arm. Next remove front pivot bolt nut from lower arm, also rear bushing bracket bolts, and detach control arm from frame. In case of 4WD models before you take off ball joint out of steering knuckle first remove driveaxle. Look carefully at bushings for wear, hardening, or cracks where necessary replacing them. Forward control arm bushing is replaceable with special tools while rear bushing can be slid off pin of control arm Installation follows the reverse of the removal process except ensuring proper tightening of including torque values for wheel lug nuts as well as pivot bolt nut or bushing bracket bolts.

Genuine Nissan Frontier Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Control Arms found

View related parts
Nissan Frontier Link Complete-Front Suspension,Upper RH
Part Number: 54524-EA000
$85.87 MSRP: $142.70
You Save: $56.83 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: 54524-EA00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2019 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete-Front Suspension, Lower Rh
Part Number: 54500-EA00A
$46.35 MSRP: $68.38
You Save: $22.03 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower RH
- Position: Passenger Side
- Replaced by: 54500-9CD0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2013 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete-Front Suspension,Upper LH
Part Number: 54525-EA000
$85.87 MSRP: $148.43
You Save: $62.56 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver side
- Replaced by: 54525-EA00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2019 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link COMPL-FRT Suspension UPPR
Part Number: 54524-EA00A
$93.82 MSRP: $142.70
You Save: $48.88 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Upper Control Arm
- Position: Passenger Side
- Replaces: 54524-EA000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2024 Nissan Frontier | LE, Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 3.8 L GAS, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link COMPL-FRT Suspension UPPR
Part Number: 54525-EA00A
$97.58 MSRP: $148.43
You Save: $50.85 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Upper Control Arm
- Position: Driver side
- Replaces: 54525-EA000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2024 Nissan Frontier | LE, Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 3.8 L GAS, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete Front Suspension, Lower Lh
Part Number: 54501-EA00A
$48.42 MSRP: $68.38
You Save: $19.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower LH
- Position: Driver side
- Replaced by: 54501-9CD0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2013 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete-Front Suspension, Lower Rh
Part Number: 54500-9CD0A
$46.35 MSRP: $68.38
You Save: $22.03 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower RH
- Position: Passenger Side
- Replaced by: 54500-9CD0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Frontier | PRO-4X, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete Front Suspension, Lower Lh
Part Number: 54501-9CD0A
$46.35 MSRP: $68.38
You Save: $22.03 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower LH
- Position: Driver side
- Replaced by: 54501-9CD0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Frontier | PRO-4X, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete-Front Suspension,Lower LH
Part Number: 54501-8B525
$291.93 MSRP: $382.85
You Save: $90.92 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STAMPED 54501-8B500
- Position: Driver side
- Replaced by: 54501-9Z510
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2000 Nissan Frontier | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Arm Anchor RH
Part Number: 54210-9Z000
$106.99 MSRP: $142.65
You Save: $35.66 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assy-Anchor,Front Suspension RH; Anchor, Torque Arm Anchor, Torsion Bar Anchor End
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2004 Nissan Frontier | SC, SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Link Complete-Front Suspension,Lower RH
Part Number: 54500-8B525
$291.93 MSRP: $382.85
You Save: $90.92 (24%)
ADD TO CART
Limited Availability
Product Specifications
- Manufacturer Note: STAMPED 54500-8B500
- Position: Passenger Side
- Replaced by: 54500-9Z510
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2000 Nissan Frontier | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Link Complete-Front Suspension Upper
Part Number: 54525-1Z600
$101.13 MSRP: $134.83
You Save: $33.70 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Upper LH; Upper Control Arm
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2002-2004 Nissan Frontier | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Link COMPL-Transverse,RH
Part Number: 54500-9CD0C
$46.35 MSRP: $68.38
You Save: $22.03 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Control Arm
- Position: Passenger Side
- Replaces: 54500-EA000, 54500-EA00A, 54500-9CD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Frontier | PRO-4X, PRO-X, S, SV | 6 Cyl 3.8 L GAS
View related parts
Nissan Frontier Link COMPL-Transverse,LH
Part Number: 54501-9CD0C
$46.35 MSRP: $68.38
You Save: $22.03 (33%)
ADD TO CART
Product Specifications
- Other Name: Lower Control Arm
- Position: Driver Side
- Replaces: 54501-EA000, 54501-9CD0A, 54501-EA00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Frontier | PRO-4X, PRO-X, S, SV | 6 Cyl 3.8 L GAS
View related parts
Nissan Frontier Link Complete - Front Suspension, Lower RH
Part Number: 54500-3S550
$134.16 MSRP: $178.88
You Save: $44.72 (25%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower RH
- Position: Passenger Side
- Replaced by: 54500-9Z500
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2001 Nissan Frontier | SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Link Complete - Front Suspension, Lower LH
Part Number: 54501-3S550
$134.16 MSRP: $178.88
You Save: $44.72 (25%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower LH
- Position: Driver side
- Replaced by: 54501-9Z500
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2001 Nissan Frontier | SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Link Complete-Front Suspension,Upper LH
Part Number: 54525-8B525
$136.99 MSRP: $182.65
You Save: $45.66 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STAMPED 54525-8B500
- Position: Driver side
- Replaced by: 54525-8B550
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2000 Nissan Frontier | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Link Complete-Front Suspension, Lower Rh
Part Number: 54500-9Z555
$291.93 MSRP: $382.85
You Save: $90.92 (24%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower RH
- Position: Passenger Side
- Replaced by: 54500-9Z510
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Link Complete-Front Suspension, Lower Rh
Part Number: 54500-ZG90B
$213.97 MSRP: $325.48
You Save: $111.51 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower RH
- Position: Passenger Side
- Replaced by: 54500-9CD0D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2009 Nissan Frontier | LE, Off-Road, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Link Complete Front Suspension, Lower Lh
Part Number: 54501-ZG90B
$213.97 MSRP: $325.48
You Save: $111.51 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Complete-Front Suspension,Lower LH
- Position: Driver side
- Replaced by: 54501-9CD0D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2009 Nissan Frontier | LE, Off-Road, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE

| Page 1 of 3 |Next >

1-20 of 52 Results

Nissan Frontier Control Arm

If you need any OEM Nissan Frontier Control Arm, feel free to choose them out of our huge selection of genuine Nissan Frontier Control Arm. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Frontier Control Arm Parts Questions & Experts Answers

Link Complete-Front Suspension,Lower LH
54501-8B525
Q: How to remove and install lower control arms on Nissan Frontier?
A: To avoid mistakes and properly remove and install lower control arms on a two-wheel drive Frontier and two-wheel Xterra models,Firstly, loosen wheel lug nuts, lift a vehicle, and support it with jack stands placed under the frame rails. Take off the wheel then remove torsion bar and torque arm. At this moment you can separate stabilizer bar link from lower control arm. Later remove shock absorbers lower mounting bolt. In case of 2WD Frontier models, release tension rod from the bottom arm. To get your lower control arm off Steering Knuckle, slightly loose balljoint nut before using balljoint separator to relieve balljoint from knuckle. Then take out nut. Thereafter, you can proceed to remove the lower control arm pivot bolt(s) and nut(s) by watching the way they were facing when these steps are done lower control arm could be removed for replacement if necessary. Finally reinstalling is in reverse order of removal except ensuring proper tightening of nuts and bolts or wheel lug nuts as well as alignment checks as outlined in instructions For 4WD Frontier and 4WD Xterra models: Start by loosening wheel lug nuts; raise vehicle and secure with jackstands under frame rails; remove wheel; then remove locking hub assembly along with snap-ring from driveaxle; next take out torsion bar along with torque arm; undo stabilizer bar link from the low control arm; finally unbolt shock absorber low mounting bolt. Unbolt driveaxle inner CV joint from differential drive flange. Remove lower control arm pivot bolts/nuts, separate lower control arm from frame brackets, support driveaxle to prevent it from hanging by outer CV joint. Gently tap end of driveaxle with soft face hammer to disengage driveaxle from hub splines, then pull out axle shaft assembly.; remove cotter pin then back-off (but do not remove) nut from lower ball joint; employ a two-jaw puller to free the ball-stud from steering knuckle; and finally turn off nuts and disconnect lower control arm from steering knuckle. Inspect bushings for wear, hardening, or cracks if found replace bushings. Finally reinstalling is in reverse order of removal except ensuring proper tightening of nuts and bolts or wheel lug nuts as well as torque values for the driveaxle inner flange bolts and the locking hub bolts. For Pathfinder models: Start by loosening wheel lug nuts; raise vehicle and support with jackstands beneath subframe rails; remove wheel; then remove balljoint-to-lower control arm nuts (on Pathfinder models, you can unbolt the balljoint from the control arm by removing the three nuts). Pull up on balljoint to separate it from control arm. Next remove front pivot bolt nut from lower arm, also rear bushing bracket bolts, and detach control arm from frame. In case of 4WD models before you take off ball joint out of steering knuckle first remove driveaxle. Look carefully at bushings for wear, hardening, or cracks where necessary replacing them. Forward control arm bushing is replaceable with special tools while rear bushing can be slid off pin of control arm Installation follows the reverse of the removal process except ensuring proper tightening of including torque values for wheel lug nuts as well as pivot bolt nut or bushing bracket bolts.