Nissan 26296-89947 Bulb

You can Select Your Vehicle to check if 26296-89947 fits your vehicle.

To access the front parking/turn signal and side marker lights, detach the plastic inner fender liner at the front edge and pull it back to reach the bulbs; for 2010 and earlier models, the side marker bulb can be accessed from under the hood. Turn the bulb sockets counterclockwise and pull them out of the housing, then remove the bulb from the bulb holder, with installation being the reverse of removal. For the rear turn signal, brake, tail, side marker, and back-up lights, remove the rear trim panel from the trunk interior by taking out the plastic fasteners, then unclip the trunk interior liner to access the rear taillight assembly. Remove the nuts from the studs, take out the taillight assembly by prying it rearward, twist the bulb holder counterclockwise to pull it from the housing, and remove the bulb from the holder, with installation reversing the removal steps. For fog lights, detach the plastic inner fender liner at the front edge, disconnect the electrical connector from the bulb holder, turn the bulb holder counterclockwise to pull it out, and reinstall by reversing the steps. To replace the license plate light, loosen the trunk lid finish panel, twist the bulb socket counterclockwise to remove it, pull the bulb out to replace it, and reinstall by reversing the steps. For the high-mounted brake light, push the housing to the rear, release the front mounting tabs, slide it to the front to release the rear tabs, lift the housing, twist the bulb socket counterclockwise to remove it, pull the bulb out to replace it, and reinstall by reversing the steps. Interior light bulbs are replaced by carefully prying off the lens with a small screwdriver or trim tool, pulling the bulb straight out of its socket, replacing it, and snapping the lens back in place; for the trunk light bulb, release the tab on the side of the lens, pivot it open, and replace the bulb as described. Instrument cluster illumination is contained within the cluster, and if there is a problem with any of its components, the entire cluster should be replaced.

The front turn signal, park light and side marker light are actually installed in the head light assembly where the round shaped bulb is the combined turn/park bulb while the smaller bulb is the side marker bulb. To access these, depower the front corner inner fender well liner mounting fasteners, and pull the liner backward. The side marker or turn signal is located behind the headlight housing, you must twist the holder counter clockwise to un-lock it before pulling the light bulb straight out of the socket and vise versa when putting in the bulb. For tail and back-up lights on those models of Titan which are equipped with such options, open the tailgate, and then unscrew the mounting fasteners and pulling the taillight housing from the specified side of the bed. Location of the liftgate in Armada models and then unbolt the two maintaining screws and take out the taillight housing while the installing, do remember to fit the projected pin with the holes in the body. Twist the bulb holder anti clock wise and this will release the bulb socket from the housing for you to replace the bulb. Replacing the license plate light is little complex and for Titan models the housing has to be pulled from the bumper and for the Armada the housing has to be unsnapped and the bulb holder needs to be replaced. The brake light is situated at the rear of the interior roof headliner on the Titan models, and to change the bulb holders one has to pry out two plastic covers, then come in and pull out the assembly to twist out the holders. Armada styles are also modelled in the same way. The lights on it are I think part of the circuit board and cannot be replaced. Replace the bulb for interior lights by pulling off the lens for the map lights or dome light using a screwdriver. For the fog lights, locate the electrical connecter at the rear of the front bumper behind the fog light housing, unscrew the bulb in a counter clockwise direction and in replacing, do not touch the surface of the new bulb with fingers as this causes overheating; if done, clean with rubbing alcohol. Installation is the process of putting some fixtures and making them function in the ideal state; this is the opposite of removal.

To access the exterior lights, locate the bulb sockets in the headlight housing from the engine compartment. For SE-R models, remove the air filter resonator to reach the left side bulbs.

Remove the liftgate trim panel, disconnect the electrical connector, remove the retaining nuts, and reinstall in reverse order.