Nissan B6296-4A001 Bulb

You can Select Your Vehicle to check if B6296-4A001 fits your vehicle.

To replace the front parking and turn signal lights, remove the grille, turn the bulb socket counterclockwise to pull it out, and then remove the bulb from the holder before reversing the process for installation. For the front side marker lights, detach the rubber fender shield, turn the bulb socket counterclockwise, remove the bulb, and reinstall in reverse order. For the rear turn signal and side marker lights, open the liftgate, remove the taillight trim panel, take out the taillight assembly, twist the bulb holder counterclockwise to remove the bulb, and reinstall in reverse order. For fog lights, detach the plastic inner fender liner, disconnect the electrical connector, turn the bulb holder counterclockwise to remove the bulb, and reinstall in reverse order. For the license plate light, remove the liftgate trim panel, twist the bulb socket counterclockwise to pull it out, remove the bulb, and reinstall in reverse order. The high-mounted stop light uses LEDs and requires the entire unit to be replaced if it doesn't light; pry off the access panel, disconnect the wiring, and remove the mounting nuts before reinstalling in reverse order. For back-up lights, remove the liftgate trim panel, take out the mounting nuts and clip, pull the housing out, turn the bulb holder counterclockwise to remove the bulb, and reinstall in reverse order. Interior lights are replaced by prying off the lens, pulling the bulb straight out, replacing it, and snapping the lens back in place; for the trunk light, release the tab on the lens to pivot it open for bulb replacement. Instrument cluster illumination issues require replacing the entire cluster if any individual components fail.

To replace exterior lights begin with the front parking and turn signal lights removes the head light housing, rotate the bulb socket anti clock wise to pull it, remove bulb from the holder, and the procedure of installation is reversed. For rear turn signal, brake, tail, side marker, and back-up lights on hatchback models, the rear access panels must be removed having two nuts at the studs, which must be unscrewed and after that the assembly must be pulled straight back; the bulb holder must be twisted in anticlockewise direction in order to unlock it from its place and then the bulb has to be removed, also in reverse order. For models of sedans, first, take out the trunk inner trim, then by twisting it clockwise the bulb can be detached, and then reinstall it in a reverse manner. To replace the fog light bulb you will have to remove the inner fender splash shield partially to have access to it, then you have to unscrew the electrical connector, rotate the bulb holder anti-clockwise in order to pull it out, and finally reuse in the reverse method. For assembly removal and installation of fenders, partly remove the inner fender splash shield and lower cover, disconnect the electrical connector, unlock the pawl, unscrew the mounting bolt of fender finish panel and secure back in a reversed manner. On license plate lights on the hatches, compression has to be done on the latching pawl to unlock it, then the fixture can be pulled down and bulb removed, followed by an installation process in the reverse manner. For sedan models, first, to remove the nuts, homeowners have to eliminate the trunk lid trim finisher, to follow, get rid of the license plate fixture, next twist the bulb socket in the counter clockwise direction to pull it out and finally, to get rid of the bulb and reinstall everything in the opposite manner. The high-mounted brake light assembly on hatchback models involved the removal of the lift gate trim panel and this makes it easy to access the electrical connector that has to be disconnected, to get at the retaining nuts which also have to be removed and for the replacement of the high-mounted brake light assembly the above sequences have to be followed in reverse, sedan models with a rear air spoiler, requires the removal of the spoiler then the high-mounted brake light trim followed For those sedans that do not have the feature of rear air spoiler, then you can proceed to lose the rear parcel shelf, the mounting screws and the assembly, but install them in the reverse order. If you want to replace the bulb and the fixture is located inside the trunk, the steps are simply as follows; unscrew the fixture anti-clockwise, take out the bulb and replace in a similar manner. Interior light bulbs are removed by popping off the lens with a flat head screwdriver or trim stick and gently pulling the bulb out with fingers and then inserting in the reverse way. For illumination of instruments like the speedometer, odometer, and other gadgets, if there is an issue with any of the gadgets, change the whole cluster as it forms a single unit.

When renewing a bulb, disconnect the battery negative terminal, be cautious of hot bulbs, and ensure clean metal-to-metal contact between the bulb and its holder, cleaning off any corrosion or dirt. For bayonet-type bulbs, ensure the live contacts are secure against the bulb. Always use a bulb of the correct rating and handle it with a tissue or clean cloth to avoid skin contact, which can cause rapid failure; if touched, clean with methylated spirit. For headlight bulbs, disconnect the wiring connector, remove the protective cover, and pivot the retaining spring clip to withdraw the bulb. Install the new bulb correctly, secure it with the spring clip, and replace the cover. For the dipped beam, remove the protective cover, rotate the bulbholder anti-clockwise, disconnect the wiring, and install the new bulb by turning it clockwise. For the main beam, follow a similar process but rotate the bulbholder clockwise to remove and anti-clockwise to install. For sidelights, disconnect the wiring, twist the bulbholder to remove, and fit the new bulb. For front indicators, twist the bulbholder anti-clockwise, remove the bulb, and fit the new one. For the front foglight, remove the inner wheel arch liner, disconnect the wiring, and turn the bulbholder anti-clockwise to remove the bulb. For rear lights, open the tailgate, undo the retaining bolts, withdraw the light unit, and turn the bulbholder anti-clockwise to remove the bulbs. For the rear fog light, extract the plastic rivet, pull down the bumper, and turn the bulbholder anti-clockwise to remove the bulb. For the number plate light, unclip the light unit, turn the bulbholder anti-clockwise, and pull the bulb to remove it, then fit the new bulb.

Disconnect the electrical connector from the headlight bulb holder, then twist the bulb counterclockwise to remove it from the housing.

Models equipped with halogen bulbs have separate headlight bulbs for the high and low beams.

Pry out the trim panel, remove the mounting screws on non-Select models, push the housing to the right, disconnect the electrical connector, and remove the bulb.

Disconnect the bulb holder electrical connector.

Remove the washer fluid reservoir.