How to remove and install the front brake disc and other parts of a Nissan 240sx?

To replace the parts for 200SX and 240SX models equipped with the rear-wheel drive system, first securely lift and support the front part of the vehicle and then, take off the wheels. Secondly, remove the brake caliper assembly and depending on vehicle, the wheel hub and bearing assembly while observing that the brake hose should not be twisted. To disassemble, take off the brake disc/wheel hub from the car; for assembly, do the reversal of the above steps, and if necessary, center the bearings. For examination, rubbing should feel rough, having visible cracks or chips and it should be noted that rotors should be machined or replaced every time front disc brake pads are changed. For models with front-wheel drive Stanza as well as Stanza Wagon, be careful as brake shoes possess asbestos, which is known to be carcinogenic; do not clean using compressed air but instead use brake cleaning fluid. For early type rotor/disc assembly, the removal of the caliper, cylinder body, and torque member from the steering knuckle without removing the brake tube, where applicable must be done followed by supporting of the part. But before the setting up of the actual drive shaft, take off the grease cap, cotter pin, adjusting cap, wheel bearing locknut, and the thrust washer from the drive shaft. There are specific wheel hub remover tools for pushing the wheel hub/disc assembly off the steering knuckle, after which the disc-to-wheel hub bolts must be unscrewed to allow the two elements to unscrew. After that, you have to assemble the wheel hub/disc assembly back into the vehicle, tightening the bolts to the prescribed torque and following the service procedures, and reinstall the caliper assembly together with all governing components, if applicable, including bleeding the brake fluids. For later type rotor/disc assembly unit, firstly, safely elevate the vehicle, then, take off the caliper assembly and follow by the removal of the rotor/disc assembly and the installation procedure would be in the opposite manner. Roughness, cracks, or chips on the brake rotor should always be noticed and one should always understand that machining or replacement of the rotor is needed during every front disc brake pad replacement.

What steps should be taken to renew front brake discs and ensure proper installation on Nissan Juke?

If either disc requires renewal, both should be renewed at the same time to ensure even and consistent braking, and new brake pads should also be fitted. Firmly apply the handbrake, jack up the front of the vehicle, and support it securely on axle stands before removing the appropriate front roadwheel. Slowly rotate the brake disc to check both sides; if better access is needed, remove the brake pads. Light scoring is normal, but heavy scoring or cracks indicate the disc must be renewed. A lip of rust and brake dust may be present around the disc's perimeter, which can be scraped off if necessary. If a lip has formed due to excessive wear, measure the disc's thickness with a micrometer at several points; if it has worn to the specified minimum thickness or less, renewal is required. To check for warping, measure run-out using a dial gauge or feeler blades; excessive measurements indicate the disc must be renewed, but check the hub bearing first. Inspect the disc for cracks and other damage, renewing if necessary. To remove the disc, apply the handbrake, jack up the vehicle, and remove the front roadwheel. Unscrew the bolts securing the caliper mounting bracket to the hub carrier, withdraw the caliper assembly, and suspend it without straining the brake fluid hose. If the original disc is to be refitted, mark its relationship with the hub before pulling it from the roadwheel studs. Ensure the mating faces of the disc and hub are clean and flat before refitting. Align any marks made before removal if the original disc is being reused, or wipe any preservative coating from a new disc. Refit the caliper, ensuring the pads are correctly located over the disc, and tighten the caliper mounting bracket bolts to the specified torque. Refit the brake fluid hose if applicable, then depress the brake pedal repeatedly until normal pedal pressure is restored. Repeat the procedure for the remaining brake if a new disc was fitted, then refit the roadwheel and lower the vehicle to the ground.

Genuine Nissan Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

293 Brake Discs found

View related parts
Nissan Rotor Brake
Part Number: 43206-9BE0C
$88.47 MSRP: $128.13
You Save: $39.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Replaced by:
- Replaces: 43206-EA010, 43206-9BE0A
Fits the following Nissan Models:
- Frontier | 2005-2025 | Desert Runner, Hardbody Edition, LE, Nismo Off-Road, Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5 L GAS, 4 Cyl 2.5L, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 6 Cyl 4.0L
- Xterra | 2005-2015 | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-9BE0C
$88.47 MSRP: $128.13
You Save: $39.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
- Replaces: 40206-9BE0B, 40206-EA00A, 40206-9BE0A
Fits the following Nissan Models:
- Frontier | 2005-2025 | Desert Runner, Hardbody Edition, LE, Nismo Off-Road, Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 6 Cyl 4.0L
- Pathfinder | 2005-2012 | LE, S, SE, SE Off-Road, Silver Edition, SV, XE | 6 Cyl 4.0L
- Xterra | 2005-2015 | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L
View More
View related parts
Nissan Rear Disc Brake Rotor
Part Number: 43206-CK000
$110.52 MSRP: $160.06
You Save: $49.54 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Position: Rear
- Replaced by:
- Replaces: 43206-CA000
Fits the following Nissan Models:
- Murano | 2003-2014 | LE, LE/ROOF, S, SE, SL, SL/ROOF, SV | 6 Cyl 3.5L
- Pathfinder | 2013-2020 | Platinum, Platinum Hybrid, S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Quest | 2004-2017 | Base, LE, S, SE, SL, SV | 6 Cyl 3.5L
View More
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-3TA0A
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
Fits the following Nissan Models:
- Altima | 2019-2025, 2013-2015 | 25SL/Moon Roof, Base, Edition ONE, Platinum, S, SL, SR, SV, Tech | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L, 4 Cyl 2.5 L GAS, 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-4BT0B
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Manufacturer Note: SAME AS 40206-4BA0A
- Position: Front
- Replaced by:
- Replaces: 40206-4BA0A, 40206-4BT0A, 40206-5HA0A
Fits the following Nissan Models:
- Leaf | 2013-2017 | S, SL, SV | Electric Motor
- Rogue | 2014-2020 | S, SL, SL Hybrid, SL/Premium, SV, SV Hybrid, SV Premium | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 4 Cyl 2.5L
- Rogue Sport | 2017-2022 | S, SL, SV | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L
View More
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-3JA0C
$103.53 MSRP: $149.92
You Save: $46.39 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
Fits the following Nissan Models:
- Pathfinder | 2015-2020 | Platinum, S, SL, SV | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-4BA0A
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Manufacturer Note: SAME AS 40206-4BT0A
- Position: Front
- Replaced by: 40206-4BT0B
Fits the following Nissan Models:
- Leaf | 2013-2017 | S, SL, SV | Electric Motor
- Rogue | 2016-2019 | S, SL, SV, SV Premium | 4 Cyl 2.5L
- Rogue Sport | 2017-2019 | S, SL, SV | 4 Cyl 2.0L
View More
View related parts
Nissan Disc Brake Rotor Front
Part Number: 40206-3JA0A
$103.09 MSRP: $149.30
You Save: $46.21 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Brake Rotor, Rotor
- Position: Front
- Replaced by:
Fits the following Nissan Models:
- Murano | 2015-2024 | Midnight Edition, Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Pathfinder | 2013-2016 | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L
View related parts
Nissan Rotor Brake
Part Number: 43206-4BT0B
$100.12 MSRP: $145.00
You Save: $44.88 (31%)
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Manufacturer Note: SAME AS 43206-4BA0A
- Replaced by:
- Replaces: 43206-3NF0A, 43206-4BA0A, 43206-5HA0A
Fits the following Nissan Models:
- Leaf | 2013-2025 | S, S Plus, SL, SL Plus, SV, SV Plus | BATTERY EV (EV/BEV), Electric Motor
- Rogue | 2014-2020 | Krom, S, S Krom, SL, SL Hybrid, SL/Premium, SV, SV Hybrid, SV Premium | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0L, 4 Cyl 2.5 L GAS, 4 Cyl 2.5L
- Rogue Sport | 2017-2022 | S, SL, SV | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L
View More
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-3SG0B
$85.09 MSRP: $123.23
You Save: $38.14 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Manufacturer Note: SAME AS 40206-3SG0E
- Position: Front
- Replaced by:
- Replaces: 40206-3SG0A, 40206-3ST0A, 40206-3SG0E
Fits the following Nissan Models:
- Sentra | 2013-2019 | FE, S, SL, SR, SV | 4 Cyl 1.8L
View related parts
Nissan Rear Disc Brake Rotor
Part Number: 43206-EG000
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Position: Rear
- Replaced by:
Fits the following Nissan Models:
- 350Z | 2005-2008 | 350Z, Base, Enthusiast, Touring | 6 Cyl 3.5L
- 370Z | 2009-2020 | 40th Anniversary Edition, Base, Heritage Edition, Nismo, Nismo Tech, Sport, Sport Tech, Sport Touring, Touring, Touring Sport | 6 Cyl 3.7 L GAS, 6 Cyl 3.7L
- Z | 2023-2025 | Nismo, Performance, Proto Spec, Sport | 6 Cyl 3.0 L GAS
View More
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-9FF0C
$119.27 MSRP: $172.72
You Save: $53.45 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
- Replaces: 40206-9FF0B, 40206-ZR01A, 40206-ZR00A
Fits the following Nissan Models:
- Armada | 2007-2015 | LE, LE/SL, Platinum, SE, SE/SV | 8 Cyl 5.6L
- Titan | 2007-2024 | LE, Off-Road, Platinum, Platinum Reserve, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6 L FLEX, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L
View related parts
Nissan Rotor Disc Brake Front
Part Number: D0206-ZA500
$88.47 MSRP: $128.13
You Save: $39.66 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Rotor; Rotor
- Position: Front
- Replaced by:
- Replaces: 40206-EG00B, 40206-EG000, 40206-7Y000, 40206-CA010, 40206-ZA500
Fits the following Nissan Models:
- 350Z | 2005-2008 | 350Z, Base, Enthusiast, Touring | 6 Cyl 3.5L
- 370Z | 2009-2020 | 40th Anniversary Edition, Base, Heritage Edition, Nismo, Nismo Tech, Sport, Sport Tech, Sport Touring, Touring, Touring Sport | 6 Cyl 3.7 L GAS, 6 Cyl 3.7L
- Altima | 2004-2006 | SE-R | 6 Cyl 3.5L
- Maxima | 2004-2008 | SE, SL | 6 Cyl 3.5L
- Murano | 2011-2014, 2004-2007 | LE, LE/ROOF, S, SE, SL, SL/ROOF, SV | 6 Cyl 3.5L
View More
View related parts
Nissan Rotor Disc Brake Front
Part Number: 40206-1PA1B
$92.64 MSRP: $134.17
You Save: $41.53 (31%)
ADD TO CART
Product Specifications
- Other Name: Rotor Disc Brake Front; Rotor
- Position: Front
- Replaced by:
- Replaces: 40206-1PA1A
Fits the following Nissan Models:
- NV | 2020-2021 | S, SL, SV | 6 Cyl 4.0 L GAS, 8 Cyl 5.6 L GAS
View related parts
Nissan Rotor-Disc Brake,Rear Axle
Part Number: 43206-6RR0A
$86.30 MSRP: $124.98
You Save: $38.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Position: Rear
- Replaced by: 43206-6RA0C
- Replaces: 43206-4CE0A, 43206-6RA0C, 43206-7TC0A, 43206-6RA0A, D3206-4CE0A
Fits the following Nissan Models:
- Leaf | 2020-2025 | S, S Plus, SL, SL Plus, SV, SV Plus | BATTERY EV (EV/BEV)
- Rogue | 2020-2025 | Midnight Edition, Platinum, Rock Creek, S, SL, SL Hybrid, SV, SV Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
- Rogue Sport | 2020-2022 | S, SL, SV | 4 Cyl 2.0 L GAS
View More
View related parts
Nissan Rotor-Disc Brake,Rear Axle
Part Number: 43206-6SA0A
$88.47 MSRP: $128.13
You Save: $39.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Rear Axle; Rotor
- Position: Rear
- Replaced by:
Fits the following Nissan Models:
- Murano | 2025 | Platinum, SL, SV | 4 Cyl 2.0 L GAS
- Pathfinder | 2022-2025 | Platinum, Rock Creek, S, SL, SV | 6 Cyl 3.5 L GAS
View related parts
Nissan Drum-Brake,Rear Axle
Part Number: 43206-5R00A
$85.27 MSRP: $123.50
You Save: $38.23 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Drum-Brake,Rear Axle; Brake Rotor, Drum
- Position: Rear
- Replaced by:
Fits the following Nissan Models:
- Kicks | 2021-2025 | S, SR, SV | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Nissan Disc Brake Rotor Front
Part Number: 40206-6LE0A
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
Fits the following Nissan Models:
- Kicks | 2021-2024 | SR, SV | 4 Cyl 1.6 L GAS
- Sentra | 2020-2025 | S, SR, SV | 4 Cyl 2.0 L GAS
View related parts
Nissan Rotor Brake
Part Number: 43206-1PA1B
$95.55 MSRP: $138.38
You Save: $42.83 (31%)
ADD TO CART
Product Specifications
- Other Name: Rotor Brake; Rotor
- Replaced by:
- Replaces: 43206-1PA1A
Fits the following Nissan Models:
- NV | 2020-2021 | S, SL, SV | 6 Cyl 4.0 L GAS, 8 Cyl 5.6 L GAS
View related parts
Nissan Disc Brake Rotor Front
Part Number: 40206-5RB0A
$84.93 MSRP: $123.00
You Save: $38.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Disc Brake,Front; Rotor
- Position: Front
- Replaced by:
Fits the following Nissan Models:
- Kicks | 2018-2024 | S, SR, SR PLUS, SV | 4 Cyl 1.6 L GAS, 4 Cyl 1.6L
- Kicks Play | 2025 | S | 4 Cyl 1.6 L GAS
- Versa | 2020-2025 | S, SR, SV | 4 Cyl 1.6 L GAS
View More

| Page 1 of 15 |Next >

1-20 of 293 Results

About Nissan Brake Disc

In your Nissan brake system, there is an important component named brake disc. When you succeed slowing down your speed to zero, at the same time, the brake disc connects the brake pads to produce a brake torque, further leading to a deceleration. Owing to the extreme high mechanical and thermal loads, and other factors like spray water, road grime, brake disc will fail one day. The brake disc in your Nissan will be checked during the inspection, and if your brake disc doesn't reach the standard, then it has to be replaced without negotiation. However, you can do the replacement by yourself. When you need to find a right place to buy the right part for you Nissan, we are glad to be your first choice. We, as promised, offer all Nissan genuine brake disc with a beautiful price.

Nissan Brake Disc Parts Questions & Experts Answers

RTR Dsc Brake
40206-40F01
Q:
How to remove and install the front brake disc and other parts of a Nissan 240sx?
A:
To replace the parts for 200SX and 240SX models equipped with the rear-wheel drive system, first securely lift and support the front part of the vehicle and then, take off the wheels. Secondly, remove the brake caliper assembly and depending on vehicle, the wheel hub and bearing assembly while observing that the brake hose should not be twisted. To disassemble, take off the brake disc/wheel hub from the car; for assembly, do the reversal of the above steps, and if necessary, center the bearings. For examination, rubbing should feel rough, having visible cracks or chips and it should be noted that rotors should be machined or replaced every time front disc brake pads are changed. For models with front-wheel drive Stanza as well as Stanza Wagon, be careful as brake shoes possess asbestos, which is known to be carcinogenic; do not clean using compressed air but instead use brake cleaning fluid. For early type rotor/disc assembly, the removal of the caliper, cylinder body, and torque member from the steering knuckle without removing the brake tube, where applicable must be done followed by supporting of the part. But before the setting up of the actual drive shaft, take off the grease cap, cotter pin, adjusting cap, wheel bearing locknut, and the thrust washer from the drive shaft. There are specific wheel hub remover tools for pushing the wheel hub/disc assembly off the steering knuckle, after which the disc-to-wheel hub bolts must be unscrewed to allow the two elements to unscrew. After that, you have to assemble the wheel hub/disc assembly back into the vehicle, tightening the bolts to the prescribed torque and following the service procedures, and reinstall the caliper assembly together with all governing components, if applicable, including bleeding the brake fluids. For later type rotor/disc assembly unit, firstly, safely elevate the vehicle, then, take off the caliper assembly and follow by the removal of the rotor/disc assembly and the installation procedure would be in the opposite manner. Roughness, cracks, or chips on the brake rotor should always be noticed and one should always understand that machining or replacement of the rotor is needed during every front disc brake pad replacement.
Rotor Disc Brake Front
40206-1KC1B
Q:
What steps should be taken to renew front brake discs and ensure proper installation on Nissan Juke?
A:
If either disc requires renewal, both should be renewed at the same time to ensure even and consistent braking, and new brake pads should also be fitted. Firmly apply the handbrake, jack up the front of the vehicle, and support it securely on axle stands before removing the appropriate front roadwheel. Slowly rotate the brake disc to check both sides; if better access is needed, remove the brake pads. Light scoring is normal, but heavy scoring or cracks indicate the disc must be renewed. A lip of rust and brake dust may be present around the disc's perimeter, which can be scraped off if necessary. If a lip has formed due to excessive wear, measure the disc's thickness with a micrometer at several points; if it has worn to the specified minimum thickness or less, renewal is required. To check for warping, measure run-out using a dial gauge or feeler blades; excessive measurements indicate the disc must be renewed, but check the hub bearing first. Inspect the disc for cracks and other damage, renewing if necessary. To remove the disc, apply the handbrake, jack up the vehicle, and remove the front roadwheel. Unscrew the bolts securing the caliper mounting bracket to the hub carrier, withdraw the caliper assembly, and suspend it without straining the brake fluid hose. If the original disc is to be refitted, mark its relationship with the hub before pulling it from the roadwheel studs. Ensure the mating faces of the disc and hub are clean and flat before refitting. Align any marks made before removal if the original disc is being reused, or wipe any preservative coating from a new disc. Refit the caliper, ensuring the pads are correctly located over the disc, and tighten the caliper mounting bracket bolts to the specified torque. Refit the brake fluid hose if applicable, then depress the brake pedal repeatedly until normal pedal pressure is restored. Repeat the procedure for the remaining brake if a new disc was fitted, then refit the roadwheel and lower the vehicle to the ground.